VoxConductor

LighthouseXy·VoxConductor·hardware/VoxConductor.kicad_pcb

VoxConductor PCB layout, top view — open source ESP32 board by LighthouseXy

About the VoxConductor PCB

VoxConductor is an open source ESP32 PCB design by LighthouseXy, published on GitHub under the MIT license. It is a 4-layer board measuring 52 × 50 mm, with 61 components from 33 distinct parts.

Its main chip is the ESP32-S3-WROOM-1, from the ESP32 family. Other key parts include the TLV62569DBV, MPU-6050, USBLC6-2SC6, INMP441ACEZ-R7 and MAX98357AETE+T. By type, the board carries 24 resistors, 22 capacitors, 6 ICs, 5 connectors, 2 switches and 1 transistor.

It belongs with the audio designs in this gallery.

From the project

VoxConductor — ESP32-S3 desktop intelligent voice hub with LVGL, ASR, DeepSeek, streaming TTS, weather and microSD logging

更新:2026-10-11。这里统一保存当前 KiCad 工程、制造文件与 V3-SLA 结构,旧方案和临时文件不放进活动目录。

KiCad 三个主文件与 2026-09-16 最终制板记录逐字节相同。本次整理未修改网络、铜线或器件位置,也没有生成新的投板修订。

实物屏幕接口 J2 曾旋转 180° 返修;这个改动尚未写回 KiCad,不能把当前生产图当作已修正的屏幕装配方向。FH12 立式插座要求排线金属接触面背向棕色锁扣;具体针序与原理图同时核对,不能只翻排线上电。下一次 PCB 修订需把实物接口修正纳入设计并重新审图。

V3-SLA 修复外壳 USB 左右镜像与 PCB 装入时的螺丝柱干涉,需要成套替换主壳、底盖和扬声器托架。CAD 检查已通过,树脂打印后的实际试装、线束弯折与螺纹强度仍待验证。先打印入口框和底盖,不将装配 STEP 当作单件打印模型。

Main components on the VoxConductor

VoxConductor bill of materials (BOM)

61 components, 33 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
ESP32-S3-WROOM-1
U1
1
TLV62569DBV
U2
1
MPU-6050
U3
1
USBLC6-2SC6
U4
1
INMP441ACEZ-R7
U5
1
MAX98357AETE+T
U6
1
SS8050
Q1
1
USB_C_RECEPTACLE_USB2.0_16P
USB_C_Receptacle_USB2.0_16P
J1
1
FH12-12S-0.5SVA(54)
J2
1
53261-0271
J3
1
MICRO_SD_CARD_DET2
Micro_SD_Card_Det2
J4
1
S2B-PH-K-S(LF)(SN)
J7
2
TS-1088-AR02016
SW1, SW2
1
2.2UH
2.2uH
L1
9
0.1UF
0.1uF
C1, C6, C11, C12, C14, C17, C18, C19 +1
5
10UF
10uF
C2, C5, C10, C20, C22
1
22UF
22uF
C3
1
6.8PF
6.8pF
C4
1
1UF
1uF
C7
2
DNP
C8, C9
Show 13 more
QtyPartRefs
1
10NF
10nF
C13
1
2.2NF
2.2nF
C15
1
100NF
100nF
C23
9
10K
R1, R8, R13, R14, R15, R17, R18, R23 +1
1
453K
453k
R2
2
100K
R3, R11
2
5.1K
R4, R5
3
22R
R6, R7, R16
2
4.7K
R9, R10
1
2.2K
R12
1
0R
R20
1
10R
R21
2
1K
R22, R25

VoxConductor design files

The KiCad project lives in the LighthouseXy/VoxConductor repository on GitHub; these links point at the commit this page was built from.

VoxConductor: common questions

What microcontroller does the VoxConductor use?

The VoxConductor is built around the ESP32-S3-WROOM-1, from the ESP32 family.

How big is the VoxConductor PCB?

The VoxConductor measures 52 × 50 mm, has 4 copper layers and is 1.6062 mm thick.

How many components are on the VoxConductor?

61 components, from 33 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the VoxConductor design files?

From the LighthouseXy/VoxConductor repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the VoxConductor design in my own project?

Yes, under the terms of its MIT license, which LighthouseXy chose for the repository.

Can I test firmware for the VoxConductor without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

Similar boards