Esp32-wsn telemetry node
losneoo·esp32-wsn-telemetry-node·Hardware/metsta.kicad_pcb
About the Esp32-wsn telemetry node PCB
Esp32-wsn telemetry node is an open source ESP32 PCB design by losneoo, published on GitHub. It is a 2-layer board measuring 48.1 × 48.1 mm, with 25 components from 15 distinct parts.
Its main chip is the ESP32-WROOM-32E, from the ESP32 family. Other key parts include the AP2112K-3.3, CH340C, BME280 and SGP30. By type, the board carries 10 resistors, 5 ICs, 4 capacitors, 2 transistors, 2 connectors and 2 diodes.
It belongs with the iot & wireless, sensors and power & battery designs in this gallery.
From the project
Low-power ESP32 environmental telemetry node. Includes custom KiCad hardware schematics, ESP-NOW protocol broadcasting, custom I2C drivers, and deep sleep power management.
This repository documents the complete hardware and firmware implementation of an ultra-low-power, custom-designed ESP32 environmental sensor node. I designed this system from scratch from KiCad PCB layout to FreeRTOS C firmware as a comprehensive proof-of-concept for deployable, battery-operated IoT telemetry using the connectionless ESP-NOW protocol.
The system continuously monitors temperature, humidity, barometric pressure, estimated CO2 (eCO2), and battery voltage, broadcasting the data to a central gateway before returning to a deep sleep state.
Main components on the Esp32-wsn telemetry node
Esp32-wsn telemetry node bill of materials (BOM)
25 components, 15 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | AP2112K-3.3 | SOT-23-5 | U1 |
| 1 | CH340C | SOIC-16_3.9x9.9mm_P1.27mm | U2 |
| 1 | BME280 | Bosch_LGA-8_2.5x2.5mm_P0.65mm_ClockwisePinNumbering | U3 |
| 1 | SGP30 | SGP30 | U4 |
| 1 | ESP32-WROOM-32E | ESP32-WROOM-32D | U5 |
| 2 | NPN | SOT-23 | Q1, Q2 |
| 1 | USB_C_Receptacle_USB2.0_16P | USB_C_Receptacle_GCT_USB4110 | J1 |
| 1 | Conn_01x02_Pin | JST_PH_B2B-PH-K_1x02_P2.00mm_Vertical | J2 |
| 2 | D_Schottky | D_SOD-123 | D1, D2 |
| 2 | 10uf | C_0805_2012Metric | C1, C2 |
| 2 | 0.1uf | C_0805_2012Metric | C3, C4 |
| 2 | 5k1 | R_0805_2012Metric | R1, R2 |
| 2 | 4k7 | R_0805_2012Metric | R3, R4 |
| 4 | 10k | R_0805_2012Metric | R5, R6, R7, R8 |
| 2 | 100k | R_0805_2012Metric | R9, R10 |
Esp32-wsn telemetry node design files
The KiCad project lives in the losneoo/esp32-wsn-telemetry-node repository on GitHub; these links point at the commit this page was built from.
- LayoutHardware/metsta.kicad_pcb
- SchematicHardware/metsta.kicad_sch
Esp32-wsn telemetry node: common questions
What microcontroller does the Esp32-wsn telemetry node use?
The Esp32-wsn telemetry node is built around the ESP32-WROOM-32E, from the ESP32 family.
How big is the Esp32-wsn telemetry node PCB?
The Esp32-wsn telemetry node measures 48.1 × 48.1 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Esp32-wsn telemetry node?
25 components, from 15 distinct parts. The full bill of materials is listed on this page.
Where can I download the Esp32-wsn telemetry node design files?
From the losneoo/esp32-wsn-telemetry-node repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Esp32-wsn telemetry node design in my own project?
The repository has no license, so all rights stay with losneoo. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Esp32-wsn telemetry node without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k