5 open source boards using the SGP30
Real designs built with the SGP30, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP8266
Iaq board
nkitanov
70.1 × 43.2 mm17 parts2LNo license398ESP32
Teebeutel-Hardware
entropia
72 × 121 mm152 parts2LCERN-OHL-S-2.01STM32
Ambient pcb dkaiot
LEAT-EDGE
73 × 77.5 mm166 parts2LCERN-OHL-P-2.00ESP32
Esp32-wsn telemetry node
losneoo
48.1 × 48.1 mm25 parts2LNo license0ESP8266
Iaq board
Tonio5978
70.1 × 43.2 mm17 parts2LNo license0
How designs wire the SGP30
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the SGP30 connects to, and the resistors, capacitors and other passives placed on it.
- The SDA_3 pin has a pull-up to 1.8V on 3 of 5 designs, most often 2.2 kΩ (then 10 kΩ).
- The SCL_6 pin has a pull-up to 1.8V on 3 of 3 designs, most often 2.2 kΩ (then 10 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VDD_1pin 1 | Connected to: 3.3V 100% | — |
| VSS_2pin 2 | Connected to: GND 100% | — |
| SDA_3pin 3 | Connected to: BME280 60%, SSD1306 40%, TSL2561T 40% |
|
| VDDH_5pin 5 | Connected to: 1.8V 100% | — |
| SCL_6pin 6 | Connected to: Signal 100% |
|
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Iaq board by nkitanov, Teebeutel-Hardware by entropia, Ambient pcb dkaiot by LEAT-EDGE and Esp32-wsn telemetry node by losneoo.
The SGP30 in open source designs
The gallery holds 5 open source boards using the SGP30 from 5 GitHub repositories; a typical one measures about 70.1 × 48.1 mm and carries around 25 components.
100% are two-layer designs, the rest use four layers or more, and 40% carry an open source license.
The most starred is Iaq board by nkitanov.
Parts used alongside the SGP30
What boards using the SGP30 are built for
SGP30: common questions
Where can I find a SGP30 reference design?
Each of the 5 boards on this page is a real design using the SGP30. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the SGP30 SDA_3 pin?
The SDA_3 pin has a pull-up to 1.8V on 3 of 5 designs, most often 2.2 kΩ (then 10 kΩ). Counted from the KiCad layouts of 5 open source designs using the SGP30.
What pull-up resistor is used on the SGP30 SCL_6 pin?
The SCL_6 pin has a pull-up to 1.8V on 3 of 3 designs, most often 2.2 kΩ (then 10 kΩ). Counted from the KiCad layouts of 5 open source designs using the SGP30.
What parts are used alongside the SGP30?
The BME280, CH340C, MCP73831-2-OT, MH-Z19 and PMS7003 appear in the most repositories here.
Which microcontrollers do boards using the SGP30 use?
Most are built on ESP32 (2), ESP8266 (2) and STM32 (1).
How big is a typical board using the SGP30?
The median is 70.1 × 48.1 mm, and 100% are two-layer designs.
What is the most popular open source board using the SGP30?
By GitHub stars, Iaq board by nkitanov, with 398 stars.
Can I simulate one of these boards using the SGP30 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.