Ducky board-ESP32-S3-with-1.52-inch e paper display
About the Ducky board-ESP32-S3-with-1.52-inch e paper display
Ducky board-ESP32-S3-with-1.52-inch e paper display is an open source ESP32 PCB design by MakersFunDuck, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 34.8 × 65.9 mm, with 95 components from 43 distinct parts.
Its main chip is the ESP32-S3, from the ESP32 family. Other key parts include the W25Q128JVS, MCP73831-2-OT and AMS1117-3.3. By type, the board carries 40 capacitors, 27 resistors, 6 diodes, 5 connectors, 4 ICs and 4 inductors.
It belongs with the displays & leds and power & battery designs in this gallery.
From the project
A pcb with esp32s3 with an eink display driver
This project is a custom-designed breakout board for the ESP32-S3 chip, created using KiCad 9. The board features an e-ink display (gdem0154z91 from good display) native USB-C programming support, and includes an integrated Li-Ion battery charger,
Used for both power input and firmware flashing
Integrated charger IC with status indicators
Supports single-cell Li-Ion/LiPo batteries
Main components on the Ducky board-ESP32-S3-with-1.52-inch e paper display
Ducky board-ESP32-S3-with-1.52-inch e paper display bill of materials (BOM)
95 components, 43 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3 | QFN-56-1EP_7x7mm_P0.4mm_EP4x4mm | U1 |
| 1 | W25Q128JVS | SOIC-8_5.3x5.3mm_P1.27mm | U2 |
| 1 | MCP73831-2-OT | SOT-23-5 | U3 |
| 1 | AMS1117-3.3 | SOT-223-3_TabPin2 | U4 |
| 1 | AO3401A | SOT-23 | Q1 |
| 1 | AO3400A | SOT-23 | Q3 |
| 1 | C32346 32.768 kHz | Crystal_SMD_3215-2Pin_3.2x1.5mm | Y1 |
| 1 | C5261125 40MHz(10ppm) | Crystal_SMD_2520-4Pin_2.5x2.0mm | Y2 |
| 1 | USB_C_RECEPTACLE_USB2.0_14P USB_C_Receptacle_USB2.0_14P | USB_C_Receptacle_HCTL_HC-TYPE-C-16P-01A | J1 |
| 1 | CONN_01X02_PIN Conn_01x02_Pin | PinSocket_1x02_P2.54mm_Vertical | J2 |
| 2 | CONN_01X18_PIN Conn_01x18_Pin | PinHeader_1x18_P2.54mm_Vertical | J3, J5 |
| 1 | AFC07-S24FCC-00 | Jushuo_AFC07-S24FCA-00_1x24-1MP_P0.50_Horizontal | P4 |
| 1 | Antenna | Texas_SWRA117D_2.4GHz_Left | AE1 |
| 1 | C318884 BTN | SW_Push_1P1T_XKB_TS-1187A | BTN1 |
| 1 | 15PF 15pF | C_0402_1005Metric | DNP1 |
| 1 | Flash | SW_Push_1P1T_XKB_TS-1187A | Flash1 |
| 1 | Reset | SW_Push_1P1T_XKB_TS-1187A | Reset1 |
| 2 | LED | LED_0603_1608Metric | D1, D3 |
| 4 | SS14 | D_SMA | D4, D5, D6, D7 |
| 1 | 2NH 2nH | L_0402_1005Metric | L3 |
Show 23 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 10UH 10uH | L_Ferrocore_DLG-0403 | L4 |
| 1 | DNP | L_0402_1005Metric | L5 |
| 1 | 4.7NH 4.7nH | L_0402_1005Metric | L6 |
| 10 | 10UF 10uF | C_0402_1005Metric | C2, C3, C6, C7, C8, C16, C17, C20 +2 |
| 4 | 12PF 12pF | C_0402_1005Metric | C4, C33, C37, C38 |
| 8 | 0.1UF 0.1uF | C_0402_1005Metric | C10, C11, C15, C18, C19, C22, C32, C35 |
| 3 | 1UF 1uF | C_0402_1005Metric | C13, C26, C39 |
| 1 | DNP | C_0402_1005Metric | C14 |
| 4 | 1UF 1uF | C_0603_1608Metric | C29, C30, C34, C41 |
| 1 | 15PF 15pF | C_0402_1005Metric | C31 |
| 1 | 10NF 10nF | C_0402_1005Metric | C40 |
| 8 | 4.7UF 4.7uF | C_0805_2012Metric | C48, C49, C50, C51, C52, C53, C54, C55 |
| 1 | 2K | R_0402_1005Metric | R1 |
| 2 | 33R | R_0402_1005Metric | R2, R18 |
| 6 | 10K | R_0402_1005Metric | R3, R4, R21, R22, R33, R35 |
| 2 | 200K | R_0402_1005Metric | R12, R19 |
| 2 | 5.1K | R_0402_1005Metric | R14, R17 |
| 1 | 100K | R_0402_1005Metric | R20 |
| 6 | C17168 0R | R_0402_1005Metric | R23, R26, R27, R28, R29, R30 |
| 2 | 470R | R_0402_1005Metric | R24, R25 |
| 1 | DNP | R_0402_1005Metric | R31 |
| 2 | 2.2R | R_0603_1608Metric | R34, R37 |
| 2 | C22936 1R | R_0603_1608Metric | R36, R38 |
Ducky board-ESP32-S3-with-1.52-inch e paper display design files
The KiCad project lives in the MakersFunDuck/Ducky-board-ESP32-S3-with-1.52-inch-e-paper-display repository on GitHub; these links point at the commit this page was built from.
- Layouthardware.kicad_pcb
- Schematichardware.kicad_sch
- BOMproduction/bom.csv
Ducky board-ESP32-S3-with-1.52-inch e paper display: common questions
What microcontroller does the Ducky board-ESP32-S3-with-1.52-inch e paper display use?
The Ducky board-ESP32-S3-with-1.52-inch e paper display is built around the ESP32-S3, from the ESP32 family.
How big is the Ducky board-ESP32-S3-with-1.52-inch e paper display?
The Ducky board-ESP32-S3-with-1.52-inch e paper display measures 34.8 × 65.9 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Ducky board-ESP32-S3-with-1.52-inch e paper display?
95 components, from 43 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Ducky board-ESP32-S3-with-1.52-inch e paper display design files?
From the MakersFunDuck/Ducky-board-ESP32-S3-with-1.52-inch-e-paper-display repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Ducky board-ESP32-S3-with-1.52-inch e paper display design in my own project?
Yes, under the terms of its GPL-3.0 license, which MakersFunDuck chose for the repository.
Can I test firmware for the Ducky board-ESP32-S3-with-1.52-inch e paper display without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32Open Book Abridged Edition
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1k
ESP32Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3k
ESP32Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0k
ESP32Badge
56.3 × 39 mm239 parts4LMIT4.0k
ESP32Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k
ESP32Racer
36 × 50.2 mm70 parts4LApache-2.03.8k