DD v8
makizusi·-circuit·DD_v8/DD_v8.kicad_pcb
About the DD v8 PCB
DD v8 is an open source STM32 PCB design by makizusi, published on GitHub. It is a 2-layer board measuring 100 × 60 mm, with 50 components from 23 distinct parts.
Its main chip is the STM32F446RETX, from the STM32 family. Other key parts include the MCP2551-I-SN, LP2950-3.3_TO252 and TLP627. By type, the board carries 16 connectors, 9 capacitors, 9 resistors, 8 ICs and 8 diodes.
From the project
作成した回路
Main components on the DD v8
DD v8 bill of materials (BOM)
50 components, 23 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | STM32F446RETX STM32F446RETx | LQFP-64_10x10mm_P0.5mm | U1 |
| 2 | MCP2551-I-SN | SOIC-8_3.9x4.9mm_P1.27mm | U2, U3 |
| 1 | LP2950-3.3_TO252 | TO-252-2 | U4 |
| 4 | TLP627 | DIP-4_W7.62mm_SMDSocket_SmallPads | U5, U6, U7, U8 |
| 1 | reset | PinSocket_1x02_P2.54mm_Vertical | J1 |
| 1 | SW | PinSocket_1x02_P2.54mm_Vertical | J2 |
| 1 | ST-LINK | PinSocket_1x05_P2.54mm_Vertical | J3 |
| 2 | TERM_EN | PinSocket_1x02_P2.54mm_Vertical | J4, J5 |
| 2 | power | JST_XA_S02B-XASK-1_1x02_P2.50mm_Horizontal | J6, J7 |
| 5 | power | AMASS_XT30PW-M_1x02_P2.50mm_Horizontal | J8, J9, J10, J11, J12 |
| 1 | CAN1 | JST_XA_S02B-XASK-1_1x02_P2.50mm_Horizontal | J13 |
| 1 | CAN2 | JST_XA_S02B-XASK-1_1x02_P2.50mm_Horizontal | J14 |
| 1 | SERIAL2 serial2 | JST_XA_B04B-XASK-1-A_1x04_P2.50mm_Vertical | J15 |
| 1 | SERIAL3 serial3 | JST_XA_B04B-XASK-1-A_1x04_P2.50mm_Vertical | J16 |
| 3 | LED | LED_0603_1608Metric | D1, D2, D3 |
| 1 | C3758192 D | D_0603_1608Metric | D4 |
| 4 | D | D_SOD-128 | D5, D6, D7, D8 |
| 6 | 1UF 1uF | C_0603_1608Metric | C1, C2, C3, C4, C5, C6 |
| 2 | 47U 47u | C_0603_1608Metric | C7, C9 |
| 1 | 0.1U 0.1u | C_0603_1608Metric | C8 |
Show 3 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 3 | 1k | R_0603_1608Metric | R1, R2, R3 |
| 2 | 120 | R_0603_1608Metric | R4, R5 |
| 4 | 100 | R_0603_1608Metric | R6, R7, R8, R9 |
DD v8 design files
The KiCad project lives in the makizusi/-circuit repository on GitHub; these links point at the commit this page was built from.
DD v8: common questions
What microcontroller does the DD v8 use?
The DD v8 is built around the STM32F446RETX, from the STM32 family.
How big is the DD v8 PCB?
The DD v8 measures 100 × 60 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the DD v8?
50 components, from 23 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the DD v8 design files?
From the makizusi/-circuit repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the DD v8 design in my own project?
The repository has no license, so all rights stay with makizusi. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the DD v8 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
More boards in -circuit
Earlier revisions in the repo: DD_v7, DD_v6
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k