9 open source boards using the TLP627
Real designs built with the TLP627, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
4IN14NixieShield
NEONTEC75
98.8 × 53.6 mm43 parts2LCC-BY-NC-4.026IN14NixieShield
NEONTEC75
143.9 × 53.6 mm48 parts2LCC-BY-NC-4.01Current loops
joseguerra3000
92.7 × 38.1 mm25 parts2LNo license1STM32
STM32F103 Telemetry V01
andreabadan
96 × 96 mm109 parts4LGPL-3.00STM32
Den v3
makizusi
98 × 98 mm57 parts2LNo license08IN14NixieShield
NEONTEC75
167.4 × 53.6 mm55 parts2LCC-BY-NC-4.005IN14NixieShield
NEONTEC75
110.2 × 53.6 mm44 parts2LCC-BY-NC-4.00STM32
DM v3
makizusi
98 × 98 mm57 parts2LNo license0STM32
DD v8
makizusi
100 × 60 mm50 parts2LNo license0
How designs wire the TLP627
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the TLP627 connects to, and the resistors, capacitors and other passives placed on it.
- Pin 4 has a pull-up to HV on 6 of 7 designs, most often 2.2 kΩ (then 2.4 kΩ).
- Pin 2 has a resistor to GND on 5 of 7 designs, most often 470 Ω (then 100 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 2 | Connected to: TLP627 57% · GND 29% |
|
| Pin 4 | Connected to: TLP627 57%, a connector 29% |
|
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include 4IN14NixieShield by NEONTEC75, Current loops by joseguerra3000, 6IN14NixieShield by NEONTEC75 and STM32F103 Telemetry V01 by andreabadan.
The TLP627 in open source designs
The gallery holds 9 open source boards using the TLP627 from 7 GitHub repositories; a typical one measures about 98.8 × 53.6 mm and carries around 50 components.
89% are two-layer designs, the rest use four layers or more, and 11% carry an open source license.
The most starred is 4IN14NixieShield by NEONTEC75.
Microcontrollers on boards using the TLP627
What boards using the TLP627 are built for
TLP627: common questions
Where can I find a TLP627 reference design?
Each of the 9 boards on this page is a real design using the TLP627. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the TLP627 pin 4?
Pin 4 has a pull-up to HV on 6 of 7 designs, most often 2.2 kΩ (then 2.4 kΩ). Counted from the KiCad layouts of 7 open source designs using the TLP627.
What resistor goes on the TLP627 pin 2?
Pin 2 has a resistor to GND on 5 of 7 designs, most often 470 Ω (then 100 Ω). Counted from the KiCad layouts of 7 open source designs using the TLP627.
Which microcontrollers do boards using the TLP627 use?
Most are built on STM32 (4).
How big is a typical board using the TLP627?
The median is 98.8 × 53.6 mm, and 89% are two-layer designs.
What is the most popular open source board using the TLP627?
By GitHub stars, 4IN14NixieShield by NEONTEC75, with 2 stars.
Can I simulate one of these boards using the TLP627 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.