Little drone-

Mariavrgs·little-drone-·PCB/Dragonfly/.history/Dragonfly.kicad_pcb

Little drone- PCB layout, top view — open source STM32 board by Mariavrgs

About the Little drone- PCB

Little drone- is an open source STM32 PCB design by Mariavrgs, published on GitHub under the MIT license. It is a 4-layer board measuring 66 × 58.8 mm, with 226 components from 44 distinct parts.

Its main chip is the STM32F405RGTX, from the STM32 family. Other key parts include the ICM-20602, AT32F421G8U7, FD6288Q, TPS5430DDA and AMS1117-3.3. By type, the board carries 90 resistors, 71 capacitors, 24 transistors, 15 ICs, 15 diodes and 4 connectors.

It belongs with the robotics & motion, sensors and power & battery designs in this gallery.

From the project

A custom all-in-one flight controller + ESC, built entirely from discrete ICs rather than premade modules, designed for me by me. Flight control and all 4 motor drivers live on a single 4-layer PCB, designed from scratch in KiCad.

A custom all-in-one flight controller + ESC, built entirely from discrete ICs rather than premade modules, designed for me by me. Flight control and all 4 motor drivers live on a single 4-layer PCB, designed from scratch in KiCad.

I wanted to go past just building a flight controller most DIY FC projects stop at a board that reads a gyro and outputs signals. I wanted the whole thing: FC and ESC combined on one board, IC-level design instead of stacking pre-built modules, a custom 3D-printed frame, and firmware configured to actually fly and hold up to real maneuvers, not just hover.

Main components on the Little drone-

Little drone- bill of materials (BOM)

226 components, 44 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
STM32F405RGTX
STM32F405RGTx
U1
1
ICM-20602
U2
4
AT32F421G8U7
U3, U5, U7, U9
4
FD6288Q
U4, U6, U8, U10
1
TPS5430DDA
U11
1
AMS1117-3.3
U12
1
L78L08_SO8
U13
1
AT7456E
U14
1
BMP280
U15
24
Q_NMOS_GDS
Q1, Q2, Q3, Q4, Q5, Q6, Q7, Q8 +16
1
TSX-3225
X1
1
27MHZ
Y1
1
CONN_01X04_PIN
Conn_01x04_Pin
J1
1
XT60PW-M
J7
1
CAM VIN
J8
1
VOUT
J9
1
32.768 kHz
+10ppm1
2
SW_SPST
SW1, SW2
1
LED BLUE
D1
1
LED RED
D2
Show 24 more
QtyPartRefs
12
1N914WT
D3, D4, D5, D6, D7, D8, D9, D10 +4
1
40V, 3A Schottky
D15
1
1KΩ 100Mhz
L1
1
15UH
15uh
L2
2
10PF
10pf
C1, C2
2
12PF
12pf
C3, C4
30
100NF
100nf
C5, C6, C9, C10, C11, C12, C17, C19 +22
3
2.2UF
2.2uf
C7, C8, C18
1
10NF
10nf
C13
4
1UF
1uf
C14, C61, C63, C72
24
10UF
10uf
C20, C24, C25, C27, C28, C29, C30, C31 +16
1
0.01UF
0.01uf
C58
1
220UF
220uf
C59
2
47UF
47uf
C70, C71
1
0.1UF
0.1uf
C73
1
10k NC
R1
35
10K
10k
R2, R3, R7, R8, R9, R10, R11, R15 +27
2
5.1kΩ
R4, R5
12
1k
R12, R13, R14, R30, R31, R32, R50, R51 +4
12
0R
R18, R22, R26, R42, R44, R46, R62, R64 +4
24
20R
R19, R20, R21, R23, R24, R25, R38, R39 +16
1
30.9K
30.9k
R87
1
100K
100k
R89
2
75R
R90, R91

Little drone- design files

The KiCad project lives in the Mariavrgs/little-drone- repository on GitHub; these links point at the commit this page was built from.

Little drone-: common questions

What microcontroller does the Little drone- use?

The Little drone- is built around the STM32F405RGTX, from the STM32 family.

How big is the Little drone- PCB?

The Little drone- measures 66 × 58.8 mm, has 4 copper layers and is 2.2 mm thick.

How many components are on the Little drone-?

226 components, from 44 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Little drone- design files?

From the Mariavrgs/little-drone- repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Little drone- design in my own project?

Yes, under the terms of its MIT license, which Mariavrgs chose for the repository.

Can I test firmware for the Little drone- without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

Similar boards