ESP32-S3-Flight Controller

Maxandersen1·ESP32-S3-Flight_Controller·hardware/ESP32_Flight_Conroller.kicad_pcb

ESP32-S3-Flight Controller PCB layout, top view — open source ESP32 board by Maxandersen1

About the ESP32-S3-Flight Controller PCB

ESP32-S3-Flight Controller is an open source ESP32 PCB design by Maxandersen1, published on GitHub under the MIT license. It is a 4-layer board measuring 40.5 × 48.8 mm, with 48 components from 26 distinct parts.

Its main chip is the ESP32-S3-WROOM-1, from the ESP32 family. Other key parts include the USBLC6-2SC6, BMI088, BMP388, TPS54331DG4 and AMS1117-3.3. By type, the board carries 17 capacitors, 15 resistors, 6 ICs, 4 connectors, 3 diodes and 1 inductor.

It belongs with the robotics & motion, sensors and power & battery designs in this gallery.

From the project

Custom ESP32 Flight Controller using BMI088 & BMP388 sensors. Hardware and firmware built from the ground up.

A custom-designed drone flight controller built from the ground up around the ESP32-S3 microcontroller. This project is a work-in-progress, covering everything from custom PCB design in KiCad to low-level sensor drivers and Web Serial 3D visualization.

Hardware designed from scratch by Max. Firmware and 3D visualization developed using AI-assisted pair programming.

ESP32-S3-Flight Controller, from the project README
From the project README

Main components on the ESP32-S3-Flight Controller

ESP32-S3-Flight Controller bill of materials (BOM)

48 components, 26 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
ESP32-S3-WROOM-1
U1
1
USBLC6-2SC6
U2
1
BMI088
U3
1
BMP388
U4
1
TPS54331DG4
U5
1
AMS1117-3.3
U6
1
USB_C_Receptacle_USB2.0_16P
J1
1
EXPRESSELRS_CONNECTOR
J2
1
ESC_CONNECTOR
J3
1
Conn_02x08_Odd_Even
J4
1
Knapp för boot
Boot1
1
Reset123
Reset1
3
D_Schottky
D1, D2, D3
1
15uH
L1
8
100nF
C1, C4, C5, C6, C7, C10, C15, C16
2
10nF
C2, C12
1
10uF
C3
4
22uF
C8, C9, C13, C14
1
3.3nF
C11
1
4.7uF
C17
Show 6 more
QtyPartRefs
2
5.1k
R1, R2
7
10k
R3, R4, R9, R11, R13, R14, R15
2
4.7k
R5, R6
2
100k
R7, R12
1
52.3k
R8
1
30k
R10

ESP32-S3-Flight Controller design files

The KiCad project lives in the Maxandersen1/ESP32-S3-Flight_Controller repository on GitHub; these links point at the commit this page was built from.

ESP32-S3-Flight Controller: common questions

What microcontroller does the ESP32-S3-Flight Controller use?

The ESP32-S3-Flight Controller is built around the ESP32-S3-WROOM-1, from the ESP32 family.

How big is the ESP32-S3-Flight Controller PCB?

The ESP32-S3-Flight Controller measures 40.5 × 48.8 mm, has 4 copper layers and is 1.6 mm thick.

How many components are on the ESP32-S3-Flight Controller?

48 components, from 26 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the ESP32-S3-Flight Controller design files?

From the Maxandersen1/ESP32-S3-Flight_Controller repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the ESP32-S3-Flight Controller design in my own project?

Yes, under the terms of its MIT license, which Maxandersen1 chose for the repository.

Can I test firmware for the ESP32-S3-Flight Controller without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

Similar boards