Meesho-Put-To-Light
mayoogh-flexli·Meesho-Put-To-Light·PTL-RAIL/PTL-RAIL.kicad_pcb
About the Meesho-Put-To-Light PCB
Meesho-Put-To-Light is an open source ESP32 PCB design by mayoogh-flexli, published on GitHub. It is a 2-layer board measuring 400 × 40 mm, with 98 components from 38 distinct parts.
Its main chip is the ESP32-S3-WROOM-1, from the ESP32 family. Other key parts include the TLV1117-33, TPS54360BQDDARQ1, USBLC6-2SC6, SN65HVD230DR and TSOP382xx. By type, the board carries 34 resistors, 27 capacitors, 11 diodes, 10 ICs, 5 transistors and 5 connectors.
From the project
Modular, daisy-chained 5-node IR emitter/receiver rail for the Meesho put-to-light system. Each 400 mm board has five bin positions on an 84 mm pitch. Each position has an IR LED firing out of the top edge into the bin above and a TSOP IR receiver looking out of the bottom edge i
Modular, daisy-chained 5-node IR emitter/receiver rail for the Meesho put-to-light system. Each 400 mm board has five bin positions on an 84 mm pitch. Each position has an IR LED firing out of the top edge into the bin above and a TSOP IR receiver looking out of the bottom edge into the bin below. An onboard ESP32-S3 drives the emitters, reads its own receivers and the receivers of the board above, and talks to the rest of the system over CAN. Power, CAN and the receiver signals pass from board to board through screw terminals.

Main components on the Meesho-Put-To-Light
Meesho-Put-To-Light bill of materials (BOM)
98 components, 38 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | TLV1117-33 | SOT-223-3_TabPin2 | U1 |
| 1 | TPS54360BQDDARQ1 | TPS54360BQDDARQ1 | U2 |
| 1 | ESP32-S3-WROOM-1 | ESP32-S3-WROOM-1 | U3 |
| 1 | USBLC6-2SC6 | SOT-23-6 | U4 |
| 1 | SN65HVD230DR | SOIC-8_3.9x4.9mm_P1.27mm | U5 |
| 5 | TSOP382xx | Vishay_MINICAST-3Pin | U6, U7, U8, U9, U10 |
| 5 | AO3400A | SOT-23 | Q1, Q2, Q3, Q4, Q5 |
| 1 | JST_PH_4P | JST_PH_B4B-PH-K_1x04_P2.00mm_Vertical | J1 |
| 2 | Screw_Terminal_01x10 | TerminalBlock_4Ucon_1x10_P3.50mm_Horizontal | J3, J4 |
| 2 | Screw_Terminal_01x04 | TerminalBlock_4Ucon_1x04_P3.50mm_Horizontal | J5, J6 |
| 1 | PESD1CAN_215 | SOT-23 | CR1 |
| 3 | SW_SPST | SW_SPST_PTS645Sx43SMTR92 | SW1, SW2, SW4 |
| 1 | SW_DIP_x01 | SW_DIP_SPSTx01_Slide_9.78x4.72mm_W7.62mm_P2.54mm | SW3 |
| 1 | SS36 | D_SMC | D1 |
| 1 | LED | LED_0805_2012Metric | D2 |
| 1 | SS14 | D_SMA | D3 |
| 3 | WS2812B | LED_WS2812B_PLCC4_5.0x5.0mm_P3.2mm | D4, D5, D6 |
| 5 | IR333C | LED_D5.0mm_Horizontal_O1.27mm_Z3.0mm_IRGrey | D7, D8, D9, D10, D11 |
| 1 | 15uH | L_APV_ANR8040 | L1 |
| 2 | 2.2uF | C_1210_3225Metric | C1, C3 |
Show 18 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 4 | 10uF | C_0805_2012Metric | C2, C4, C12, C13 |
| 9 | 100nF | C_0805_2012Metric | C5, C10, C16, C17, C18, C19, C20, C21 +1 |
| 1 | 22nF | C_0805_2012Metric | C6 |
| 1 | 100pF | C_0805_2012Metric | C7 |
| 2 | 22uF | C_1210_3225Metric | C8, C9 |
| 2 | 1uF | C_0805_2012Metric | C11, C15 |
| 1 | 22uF | C_0805_2012Metric | C14 |
| 5 | 4.7uF | C_0805_2012Metric | C22, C23, C24, C25, C26 |
| 1 | 274k | R_0805_2012Metric | R1 |
| 1 | 8.45k | R_0805_2012Metric | R2 |
| 1 | 60.4k | R_0805_2012Metric | R3 |
| 1 | 11.5k | R_0805_2012Metric | R4 |
| 1 | 1k | R_0805_2012Metric | R5 |
| 3 | 10k | R_0805_2012Metric | R6, R8, R34 |
| 1 | 120R | R_0805_2012Metric | R7 |
| 15 | 100R | R_0805_2012Metric | R9, R12, R15, R18, R21, R24, R25, R26 +7 |
| 5 | 100k | R_0805_2012Metric | R10, R13, R16, R19, R22 |
| 5 | 180R | R_0805_2012Metric | R11, R14, R17, R20, R23 |
Meesho-Put-To-Light design files
The KiCad project lives in the mayoogh-flexli/Meesho-Put-To-Light repository on GitHub; these links point at the commit this page was built from.
- LayoutPTL-RAIL/PTL-RAIL.kicad_pcb
- SchematicPTL-RAIL/PTL-RAIL.kicad_sch
Meesho-Put-To-Light: common questions
What microcontroller does the Meesho-Put-To-Light use?
The Meesho-Put-To-Light is built around the ESP32-S3-WROOM-1, from the ESP32 family.
How big is the Meesho-Put-To-Light PCB?
The Meesho-Put-To-Light measures 400 × 40 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Meesho-Put-To-Light?
98 components, from 38 distinct parts. The full bill of materials is listed on this page.
Where can I download the Meesho-Put-To-Light design files?
From the mayoogh-flexli/Meesho-Put-To-Light repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Meesho-Put-To-Light design in my own project?
The repository has no license, so all rights stay with mayoogh-flexli. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Meesho-Put-To-Light without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k