ESP bot
mikked2101·ESP_bot·esp_bot_pcbs/Robo.kicad_pcb
About the ESP bot PCB
ESP bot is an open source ESP32 PCB design by mikked2101, published on GitHub. It is a 4-layer board measuring 150 × 120 mm, with 51 components from 25 distinct parts.
Its main chip is the ESP32-S3, from the ESP32 family. Other key parts include the AP63203WU, BY25Q80ESTIG(T), TPS77012PDBV, USBLC6-2SC6 and L293DD. By type, the board carries 21 capacitors, 8 resistors, 7 ICs, 4 modules, 3 diodes and 3 inductors.
It belongs with the robotics & motion designs in this gallery.
From the project
A single-circuit board robot
Main components on the ESP bot
ESP bot bill of materials (BOM)
51 components, 25 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | AP63203WU | TSOT-23-6 | U1 |
| 1 | ESP32-S3 | QFN-56-1EP_7x7mm_P0.4mm_EP4x4mm_ThermalVias | U2 |
| 1 | BY25Q80ESTIG(T) | JEITA_SOIC-8_3.9x4.9mm_P1.27mm | U3 |
| 1 | TPS77012PDBV | SOT-23-5_HandSoldering | U4 |
| 1 | USBLC6-2SC6 | SOT-23-6_Handsoldering | U5 |
| 1 | L293DD | SOIC127P1032X265-20N | U6 |
| 1 | TPS77028PDBV | SOT-23-5_HandSoldering | U7 |
| 1 | ~ | PCB_Wifi_Antenna | A1 |
| 2 | Motor_DC | PinHeader_1x02_P2.54mm_Vertical | M1, M2 |
| 1 | Motor_Servo | PinHeader_1x03_P2.54mm_Vertical | M3 |
| 1 | 40MHz | XTAL_ECS-400-10-37B2-CKM-TR | Y1 |
| 1 | USB_C_Receptacle_USB2.0_16P | USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J1 |
| 1 | CF35242D0RE-NH | CONN24X1_CF35242D0RE-NH_CVI | J2 |
| 2 | SW_Push | SW_Push_1P1T_NO_E-Switch_TL3301NxxxxxG | SW1, SW2 |
| 2 | LED | LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D1, D2 |
| 1 | D_TVS | D_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D3 |
| 2 | 2n2 | L_0805_2012Metric_Pad1.15x1.40mm_HandSolder | L1, L3 |
| 1 | 3u9 | L_0805_2012Metric_Pad1.15x1.40mm_HandSolder | L2 |
| 2 | 10p | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C2 |
| 6 | 10u | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C3, C10, C15, C19, C20, C21 |
Show 5 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 11 | 100n | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C4, C5, C6, C7, C8, C9, C13, C14 +3 |
| 2 | 22u | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C11, C12 |
| 2 | 5K11 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R2 |
| 1 | 22R | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R3 |
| 5 | 10K | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R4, R5, R6, R7, R8 |
ESP bot design files
The KiCad project lives in the mikked2101/ESP_bot repository on GitHub; these links point at the commit this page was built from.
- Layoutesp_bot_pcbs/Robo.kicad_pcb
- Schematicesp_bot_pcbs/Robo.kicad_sch
ESP bot: common questions
What microcontroller does the ESP bot use?
The ESP bot is built around the ESP32-S3, from the ESP32 family.
How big is the ESP bot PCB?
The ESP bot measures 150 × 120 mm, has 4 copper layers and is 1.6062 mm thick.
How many components are on the ESP bot?
51 components, from 25 distinct parts. The full bill of materials is listed on this page.
Where can I download the ESP bot design files?
From the mikked2101/ESP_bot repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the ESP bot design in my own project?
The repository has no license, so all rights stay with mikked2101. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the ESP bot without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k