Smart room-V2
MohamadAminGhanoum·Smart-room-V2·Smart room V2/Smart room V2.kicad_pcb
About the Smart room-V2 PCB
Smart room-V2 is an open source ESP32 PCB design by MohamadAminGhanoum, published on GitHub. It is a 2-layer board measuring 94.6 × 72.5 mm, with 58 components from 32 distinct parts.
Its main chip is the ESP32-S3-WROOM-1, from the ESP32 family. Other key parts include the TPS5430DDA, AP2112K-3.3, CH224K, DS3231M and SHT4X. By type, the board carries 20 resistors, 18 capacitors, 7 ICs, 5 switches, 3 diodes and 1 transistor.
From the project
I have since around 1 year done a smart room, where i made a custom pcb, and salvaged some parts from an old laptop motherboard to be able to control the LED strip that i have and also open and close my curtain, but that was all my thing could do.
Note: The Firmware is currently only a test rn, i will upload a working code, once i make this work.
If you are interested, you can check out my V1 of this, with diy pcb: https://github.com/MohamadAminGhanoum/Smart-home
Main components on the Smart room-V2
Smart room-V2 bill of materials (BOM)
58 components, 32 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-WROOM-1 | ESP32-S3-WROOM-1 | U1 |
| 1 | TPS5430DDA | TI_SO-PowerPAD-8_ThermalVias | U2 |
| 1 | AP2112K-3.3 | SOT-23-5 | U3 |
| 1 | CH224K | SSOP-10-1EP_3.9x4.9mm_P1mm_EP2.1x3.3mm | U4 |
| 1 | DS3231M | SOIC-16W_7.5x10.3mm_P1.27mm | U5 |
| 1 | SHT4X SHT4x | Sensirion_DFN-4_1.5x1.5mm_P0.8mm_SHT4x_NoCentralPad | U6 |
| 1 | Motor controller, AM4969 | SOIC-8_3.9x4.9mm_P1.27mm | U7 |
| 1 | AO3400A | SOT-23 | Q1 |
| 1 | USB_C_RECEPTACLE_USB2.0_14P USB_C_Receptacle_USB2.0_14P | USB_C_Receptacle_XKB_U262-16XN-4BVC11 | J1 |
| 1 | Battery_Cell | BatteryHolder_Keystone_1058_1x2032 | BT1 |
| 1 | R_Potentiometer | JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | RV1 |
| 1 | Boot | SW_SPST_TS-1088-xR020 | SW1 |
| 1 | EN | SW_SPST_TS-1088-xR020 | SW2 |
| 2 | SW_Push | PinSocket_1x02_P2.54mm_Vertical | SW3, SW4 |
| 1 | POWER switch | PinSocket_1x02_P2.54mm_Vertical | SW5 |
| 1 | B340 | D_SMC | D1 |
| 2 | SS34 | D_SMA | D2, D3 |
| 1 | 22UH 22uH | L_Bourns_SRP7028A_7.3x6.6mm | L1 |
| 4 | 1UF 1uF | C_0603_1608Metric | C1, C8, C12, C15 |
| 6 | 10UF 10uF | C_0603_1608Metric | C2, C3, C9, C10, C13, C14 |
Show 12 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 0.01UF 0.01uF | C_0603_1608Metric | C4 |
| 2 | 4.7UF 4.7uF | C_0603_1608Metric | C5, C6 |
| 2 | 220UF 220uF | CP_Elec_6.3x7.7 | C7, C17 |
| 2 | 100NF 100nF | C_0603_1608Metric | C11, C16 |
| 1 | 0.1UF 0.1uF | C_0603_1608Metric | C18 |
| 1 | 6.8K 6.8k | R_0603_1608Metric | R1 |
| 8 | 10K 10k | R_0603_1608Metric | R2, R3, R5, R7, R9, R16, R17, R18 |
| 1 | 1k | R_0603_1608Metric | R4 |
| 1 | 3.24K 3.24k | R_0603_1608Metric | R6 |
| 1 | 100R | R_0603_1608Metric | R8 |
| 6 | 4.7K 4.7k | R_0603_1608Metric | R10, R11, R12, R13, R14, R15 |
| 2 | 33R | R_0603_1608Metric | R19, R20 |
Smart room-V2 design files
The KiCad project lives in the MohamadAminGhanoum/Smart-room-V2 repository on GitHub; these links point at the commit this page was built from.
Smart room-V2: common questions
What microcontroller does the Smart room-V2 use?
The Smart room-V2 is built around the ESP32-S3-WROOM-1, from the ESP32 family.
How big is the Smart room-V2 PCB?
The Smart room-V2 measures 94.6 × 72.5 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Smart room-V2?
58 components, from 32 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Smart room-V2 design files?
From the MohamadAminGhanoum/Smart-room-V2 repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Smart room-V2 design in my own project?
The repository has no license, so all rights stay with MohamadAminGhanoum. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Smart room-V2 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k