Ntex
NgHdc·Ntex
About the Ntex PCB
Ntex is an open source ESP32 PCB design by NgHdc, published on GitHub. It is a 2-layer board, with 109 components from 31 distinct parts.
Its main chip is the ESP32-C6-MINI-1, from the ESP32 family. Other key parts include the RT9080-33GJ5, MCP73831 and ADXL343. By type, the board carries 28 resistors, 15 capacitors, 10 connectors, 8 test points, 8 diodes and 7 ICs.
Main components on the Ntex
Ntex bill of materials (BOM)
109 components, 31 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | ESP32-C6-MINI-1 | ESP32-C6-MINI-1 | U1, U4 |
| 2 | RT9080-33GJ5 | SOT23-5 | U2, U5 |
| 2 | MCP73831 | SOT23-5 | U3, U6 |
| 1 | ADXL343 | LGA-14_3x5mm_P0.8mm_LayoutBorder1x6y | U7 |
| 2 | 20V/4.2A/52mΩ/1.4W | SOT23-3 | Q1, Q2 |
| 2 | USB Female Type C Connector | USB-C-16P_4LAYER-PADS | J1, J6 |
| 4 | CONN_06NO_SILK_NO_POP | 1X06_NO_SILK | J2, J3, J8, J9 |
| 2 | QWIIC_RIGHT_ANGLE | JST04_1MM_RA | J4, J7 |
| 2 | JST_2MM_MALE | JST-2-SMD | J5, J10 |
| 4 | MOMENTARY-SWITCH-SPST-SMD-4.6X2.8MM | TACTILE_SWITCH_SMD_4.6X2.8MM | BOOT0, BOOT1, RESET0, RESET1 |
| 6 | JUMPER-SMT_2_NC_TRACE_SILK | SMT-JUMPER_2_NC_TRACE_SILK | CHG0, CHG1, PWR0, PWR1, SHLD0, SHLD1 |
| 8 | FIDUCIALUFIDUCIAL | FIDUCIAL-MICRO | FD1, FD2, FD3, FD4, FD5, FD6, FD7, FD8 |
| 2 | FRAME-LETTER | CREATIVE_COMMONS | FRAME1, FRAME2 |
| 8 | STAND-OFF | STAND-OFF | H1, H2, H3, H4, H5, H6, H7, H8 |
| 2 | JUMPER-SMT_3_2-NC_TRACE_SILK | SMT-JUMPER_3_2-NC_TRACE_SILK | I2C0, I2C1 |
| 1 | SPH0645LM4H | Knowles_SPH0645LM4H-6_3.5x2.65mm | MK1 |
| 8 | TEST-POINT3 | PAD.03X.03 | TP1, TP2, TP3, TP4, TP5, TP6, TP7, TP8 |
| 2 | LED-RED_0603-KB | LED-0603 | D1, D6 |
| 2 | BLUE | LED-0603 | D2, D7 |
| 2 | 1A/23V/620mV | SOD-323 | D3, D5 |
Show 11 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | Yellow | LED-0603 | D4, D8 |
| 8 | 2.2uF | 0402-TIGHT | C1, C2, C3, C4, C7, C10, C11, C12 |
| 3 | 0.1uF | 0402-TIGHT | C5, C8, C15 |
| 2 | DNP | 0402-TIGHT | C6, C9 |
| 1 | 1uF | 0402-TIGHT | C13 |
| 1 | 220pF | 0402-TIGHT | C14 |
| 6 | 4.7k | 0402-TIGHT | R1, R9, R10, R25, R27, R28 |
| 6 | 2.2k | 0402-TIGHT | R2, R3, R4, R15, R18, R26 |
| 4 | 5.1k | 0402-TIGHT | R5, R6, R16, R17 |
| 8 | 100k | 0402-TIGHT | R7, R8, R11, R12, R19, R20, R23, R24 |
| 4 | 1M | 0402-TIGHT | R13, R14, R21, R22 |
Ntex design files
The KiCad project lives in the NgHdc/Ntex repository on GitHub; these links point at the commit this page was built from.
- Layoutntex.kicad_pcb
- Schematicntex.kicad_sch
Ntex: common questions
What microcontroller does the Ntex use?
The Ntex is built around the ESP32-C6-MINI-1, from the ESP32 family.
How big is the Ntex PCB?
The Ntex has 2 copper layers and is 1.6 mm thick.
How many components are on the Ntex?
109 components, from 31 distinct parts. The full bill of materials is listed on this page.
Where can I download the Ntex design files?
From the NgHdc/Ntex repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Ntex design in my own project?
The repository has no license, so all rights stay with NgHdc. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Ntex without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in Ntex
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k