Bpw34 receiver
nguyenhuy0426·PPG_simulator·hardware/bpw34_receiver/bpw34_receiver.kicad_pcb
About the Bpw34 receiver PCB
Bpw34 receiver is an open source PCB design by nguyenhuy0426, published on GitHub under the MIT license. It is a 2-layer board measuring 70 × 20 mm, with 23 components from 13 distinct parts.
Other key parts include the OPA333AIDBVR. By type, the board carries 8 capacitors, 8 resistors, 3 connectors, 2 ICs and 2 diodes.
It belongs with the audio and test & measurement designs in this gallery.
From the project
The PPG Signal Simulator is a portable device that generates synthetic PPG (photoplethysmography) waveforms with physiologically accurate morphology. It outputs the signal via a 12‑bit DAC for connection to patient monitors, oscilloscopes, or data acquisition systems.
This is a complete KiCad 10 project for a 70 x 20 mm, two-channel photodiode receiver that can replace the dual-OPT101 board mechanically. The optical centres remain 38.5 mm apart. The new screwless U support shares the enclosure slot; PCB mounting holes are removed.
Each channel is independent and contains one BPW34, one OPA333 transimpedance amplifier, a 1 Mohm feedback resistor, and a 22 pF C0G/NP0 feedback capacitor. A 100k/10k divider creates a filtered 0.30 V reference from the 3.3 V Grove supply. Light-induced reverse current therefore raises the output:
Main components on the Bpw34 receiver
Bpw34 receiver bill of materials (BOM)
23 components, 13 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | OPA333AIDBVR | SOT23_5_Hand | U1, U2 |
| 1 | A2 / RED | Header_1x04_P2mm | J1 |
| 1 | A0 / IR | Header_1x04_P2mm | J2 |
| 1 | ADS1115: RED/GND/IR/GND | Header_1x04_P2.54mm | J3 |
| 1 | BPW34 BPW34 RED | BPW34_THT | D1 |
| 1 | BPW34 BPW34 IR | BPW34_THT | D2 |
| 2 | 22pF C0G | C0805_Hand | C1, C2 |
| 4 | 100nF X7R | C0805_Hand | C3, C4, C5, C6 |
| 2 | 1uF X7R 16V | C0805_Hand | C7, C8 |
| 2 | 1M 1% | R0805_Hand | R1, R2 |
| 2 | 1k 1% | R0805_Hand | R3, R4 |
| 2 | 100k 1% | R0805_Hand | R5, R6 |
| 2 | 10k 1% | R0805_Hand | R7, R8 |
Bpw34 receiver design files
The KiCad project lives in the nguyenhuy0426/PPG_simulator repository on GitHub; these links point at the commit this page was built from.
Bpw34 receiver: common questions
How big is the Bpw34 receiver PCB?
The Bpw34 receiver measures 70 × 20 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Bpw34 receiver?
23 components, from 13 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Bpw34 receiver design files?
From the nguyenhuy0426/PPG_simulator repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Bpw34 receiver design in my own project?
Yes, under the terms of its MIT license, which nguyenhuy0426 chose for the repository.
More boards in PPG_simulator
Similar boards
StackLink
gusmanb
52.3 × 10.5 mm5 parts2LGPL-3.05.0kLevelShifter
gusmanb
28.3 × 39.8 mm21 parts2LGPL-3.05.0kAnalyzerBoxPCB fork
gusmanb
52.7 × 47.9 mm54 parts4LGPL-3.05.0kKLOR
GEIGEIGEIST
160.2 × 118.3 mm79 parts2LGPL-3.01.2kUSB
shanteacontrols
52 × 12.6 mm6 parts2LApache-2.0956Pots
shanteacontrols
390 × 93 mm75 parts2LApache-2.0956