HardLabs

Cyberboard Panel

notaroomba·cyberboard·hardware/panel/Cyberboard_Panel.kicad_pcb

Cyberboard Panel PCB layout, top view — open source STM32 board by notaroomba

About the Cyberboard Panel PCB

Cyberboard Panel is an open source STM32 PCB design by notaroomba, published on GitHub. It is a 4-layer board measuring 51 × 44 mm, with 64 components from 36 distinct parts.

Its main chip is the STM32WB55RGVX, from the STM32 family. Other key parts include the SZYY0402Y_C434450, TPD2EUSB30, NX2012SA-32.768KHZ-STD-MUB-2, BQ24072RGT and TPS631000DRLR. By type, the board carries 27 capacitors, 16 resistors, 10 ICs, 2 connectors, 2 switches and 2 inductors.

It belongs with the sensors, power & battery and dev boards & breakouts designs in this gallery.

From the project

A cyberpunk-themed STM32 devboard

- STM32WB55CG microcontroller with Bluetooth support - Raspberry Pi Pico form factor for compatibility - IMU and Barometer - ICM-42688 (6-axis) and BMP580 pressure sensor for environmental/motion sensing - Battery charging with BQ24072RGTR IC and solder pad for 1S LiPo - Buck-Boost converter (TPS631000) for efficient power management - Multiple Status LEDs for visual feedback - USB-C connectivity - Ceramic Bluetooth antenna with impedance matching - SWD test points on the bottom for easy programming - 4-layer PCB design with optimized RF layout and routing - Panelized design for…

Cyberboard Panel, from the project README
From the project README

Main components on the Cyberboard Panel

SZYY0402Y_C434450TPD2EUSB30NX2012SA-32.768KHZ-STD-MUB-2STM32WB55RGVXBQ24072RGTTPS631000DRLRICM-42688-PCBMP580C882955XL-1005UBC_C22355736

Cyberboard Panel bill of materials (BOM)

64 components, 36 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
SZYY0402Y_C434450
U1
1
TPD2EUSB30
U2
1
NX2012SA-32.768KHZ-STD-MUB-2
U3
1
STM32WB55RGVX
STM32WB55RGVx
U4
1
BQ24072RGT
U5
1
TPS631000DRLR
U6
1
ICM-42688-PC
U7
1
BMP580
U8
1
C882955
DFE252012P-1R0M=P2
U9
1
XL-1005UBC_C22355736
U10
1
NX2016SA-32MHZ-STD-CZS-5
X1
2
CONN_01X20
Conn_01x20
J1, J2
1
2450AT18A100E
AE1
1
MLPF-WB55-01E3
FL1
2
SW_Push
SW1, SW2
1
C2765186
TYPE-C 16PIN 2MD(073)
USB1
1
XL-1005UGC
LED1
1
10UH
10uH
L1
1
10NH
10nH
L2
4
10PF
10pF
C1, C2, C3, C4
Show 16 more
QtyPartRefs
11
100NF
100nF
C5, C6, C8, C10, C11, C13, C15, C16 +3
5
4.7UF
4.7uF
C7, C9, C12, C25, C26
3
1UF
1uF
C14, C17, C18
1
10NF
10nF
C19
1
22UF
22uF
C21
1
47UF
47uF
C22
1
2.2UF
2.2uF
C27
4
10K
R1, R5, R6, R13
2
5.1K
R2, R3
1
150
R4
1
1.18K
R7
1
1.13K
R8
1
511K
R9
1
91K
R10
3
4.7K
R11, R12, R16
2
1.5K
R14, R15

Cyberboard Panel design files

The KiCad project lives in the notaroomba/cyberboard repository on GitHub; these links point at the commit this page was built from.

Cyberboard Panel: common questions

What microcontroller does the Cyberboard Panel use?

The Cyberboard Panel is built around the STM32WB55RGVX, from the STM32 family.

How big is the Cyberboard Panel PCB?

The Cyberboard Panel measures 51 × 44 mm, has 4 copper layers and is 1.5842 mm thick.

How many components are on the Cyberboard Panel?

64 components, from 36 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Cyberboard Panel design files?

From the notaroomba/cyberboard repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.

Can I use the Cyberboard Panel design in my own project?

The repository has no license, so all rights stay with notaroomba. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Cyberboard Panel without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

More boards in cyberboard

Similar boards