42 open source boards using the TPD2EUSB30
Real designs built with the TPD2EUSB30, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Keyword
notaroomba
19.1 × 19.1 mm69 parts4LNo license438Icepi sbc
cheyao
85 × 56 mm265 parts4LSHL-2.1342ESP32
Air quality sensor
roepkefeller
50.8 × 45 mm75 parts4LNo license59STM32
Stm32pe midi
udu3324
307 × 46.1 mm135 parts4LGPL-3.035FPGA
M.2-FPGA-Accelerator
KaiPereira
22 × 80 mm276 parts6LNo license25STM32
Cyberboard
notaroomba
51 × 21 mm64 parts4LNo license17ESP32
LIA
JGAguado
79 × 30 mm66 parts2LCC-BY-NC-4.015AVR/Arduino
OpenPnPVis
angusgbishop
44.5 × 28 mm63 parts4LGPL-3.07RP2040/RP2350
Main board
AllenNeuralDynamics
80 × 50 mm183 parts4LMIT5FPGA
ArtixDevBoard
RasmusStagsted
92.5 × 80.9 mm300 parts4LNo license4STM32
Dreamscape-F722
sneakylizard123-4
40 × 40 mm104 parts4LNo license4ESP32
Minimap
lucapoulos
48 × 55.4 mm74 parts4LNo license2RP2040/RP2350
Valve controller
AllenNeuralDynamics
70 × 168 mm212 parts4LNo license0RP2040/RP2350
Harp.device.cuttlefish
AllenNeuralDynamics
120 × 75 mm185 parts4LNo license0ESP32
IoT Logger B
WestianPKl
94.7 × 71.8 mm135 parts2LNo license0ESP32
IoT Logger B
WestianPKl
94.7 × 71.8 mm135 parts2LNo license0AVR/Arduino
Raspberry Pi Compute Module 5 Drone Carrier
AMLing2
56.2 × 70.5 mm121 parts4LMIT0Raspberry Pi
Spha gateway hardware
sillevl
68 × 87 mm75 parts4LNo license0ESP32
Mesh rack
sneakylizard123-4
200 × 100 mm74 parts4LNo license0ESP32
Overkill nRF
sneakylizard123-4
50 × 75 mm73 parts4LNo license0ESP8266
CelestialSync
davidfobar
107 × 52 mm70 parts2LNo license0RP2040/RP2350
Usb isolated
AllenNeuralDynamics
80 × 50 mm67 parts4LNo license0ESP32
IC console
Lumosity23
50 × 50 mm65 parts4LNo license0RP2040/RP2350
Harp.device.PhotodiodeBoard
AllenNeuralDynamics
38 × 53 mm61 parts4LNo license0RP2040/RP2350
Harp.device.environment sensor
AllenNeuralDynamics
39.9 × 28 mm46 parts4LMIT0RP2040/RP2350
TellMeLight Rev A
qiaoyo
96 × 74 mm36 parts2LNo license0Port sprite
Batterhead221
51.6 × 37.8 mm34 parts4LNo license0Rak4630 interface
pashamray
50.8 × 30.5 mm18 parts2LMIT0- schematic only · 103 partsNordic nRF
Bike dynamo charger
jekhor
103 partsNo license0 STM32
Cyberboard Panel
notaroomba
51 × 44 mm64 parts4LNo license17FPGA
Anice
hackclub
65.6 × 34 mm91 parts4LNo license2Raspberry Pi
Cm4-carrier net
Unlim8ted-Studios
90 × 40 mm17 parts4LNo license2STM32
STM Board
WestianPKl
74.1 × 91.8 mm127 parts4LNo license0ESP32
IoT Logger C
WestianPKl
94.7 × 71.8 mm97 parts2LNo license0RP2040/RP2350
Usb powered small
AllenNeuralDynamics
36 × 28 mm40 parts4LNo license0RP2040/RP2350
Usb powered small
AllenNeuralDynamics
36 × 28 mm40 parts4LNo license0
How designs wire the TPD2EUSB30
Read from the KiCad layouts of 30 open source designs, one per repository: what each pin of the TPD2EUSB30 connects to, and the resistors, capacitors and other passives placed on it.
- The D+ pin has a series resistor on 13 of 30 designs, most often 22 Ω (then 27 Ω).
- The D- pin has a series resistor on 13 of 30 designs, most often 22 Ω (then 27 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| D+pin 1 | Connected to: A connector 77%, the microcontroller 37% |
|
| D-pin 2 | Connected to: A connector 77%, the microcontroller 37% |
|
| GNDpin 3 | Connected to: GND 97% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Keyword by notaroomba, Icepi sbc by cheyao, Air quality sensor by roepkefeller and Stm32pe midi by udu3324.
The TPD2EUSB30 in open source designs
The gallery holds 42 open source boards using the TPD2EUSB30 from 32 GitHub repositories; a typical one measures about 65.6 × 52 mm and carries around 72 components.
76% use four copper layers or more, and 17% carry an open source license.
The most starred is Keyword by notaroomba.
Parts used alongside the TPD2EUSB30
Microcontrollers on boards using the TPD2EUSB30
What boards using the TPD2EUSB30 are built for
TPD2EUSB30: common questions
Where can I find a TPD2EUSB30 reference design?
Each of the 42 boards on this page is a real design using the TPD2EUSB30. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the TPD2EUSB30 D+ pin?
The D+ pin has a series resistor on 13 of 30 designs, most often 22 Ω (then 27 Ω). Counted from the KiCad layouts of 30 open source designs using the TPD2EUSB30.
What resistor goes on the TPD2EUSB30 D- pin?
The D- pin has a series resistor on 13 of 30 designs, most often 22 Ω (then 27 Ω). Counted from the KiCad layouts of 30 open source designs using the TPD2EUSB30.
What parts are used alongside the TPD2EUSB30?
The RP2040, W25Q16JVUXIQ, ADUM4160, RT6150B-33GQW and 74LVCH2T45DC appear in the most repositories here.
Which microcontrollers do boards using the TPD2EUSB30 use?
Most are built on ESP32 (10), RP2040/RP2350 (10), STM32 (6) and AVR/Arduino (3).
How big is a typical board using the TPD2EUSB30?
The median is 65.6 × 52 mm, and 24% are two-layer designs.
What is the most popular open source board using the TPD2EUSB30?
By GitHub stars, Keyword by notaroomba, with 438 stars.
Can I simulate one of these boards using the TPD2EUSB30 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.