ESP
nyankowan·CatchRobo_2026·Kicad/ESP/ESP.kicad_pcb
About the ESP PCB
ESP is an open source ESP32 PCB design by nyankowan, published on GitHub. It is a 2-layer board measuring 48 × 65.9 mm, with 18 components from 12 distinct parts.
Its main chip is the ESP32_DEVKITC-32E, from the ESP32 family. By type, the board carries 7 diodes, 7 resistors, 3 connectors and 1 IC.
From the project
回路のデータ,複数マイコンのプログラム一括管理
キャチロボ2026で使用する回路データ(KiCad 10.0)と,その部品リスト.
各基板に対応するファームウェアは STM32/README.md および ESP32/controller/README.md を参照.
このディレクトリにあるキャチロボ2026に向けて作った回路データのほかにも, 岡ロボで使われるCANトランシーバー回路も使用している.
- robomascontroller基板×1 - nucleo-f446re - 192ピンソケット×2 - hirose 2pin(DF1EC-2P-2.5DSA(35))×7 - 5ピンソケット×2 - 300Ω抵抗×1 - φ3LED×1
- ESP Main controller基板×1 - ESP32-DevKitC-32E - 19ピンソケット×2 - 2ピンソケット×2 - 5ピンソケット×1 - φ3LED×7 - 470Ω抵抗×7
Main components on the ESP
ESP bill of materials (BOM)
18 components, 12 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32_DEVKITC-32E ESP32_DevKitC-32E | ESP32_DevKitC_32E | U1 |
| 1 | 5V | PinHeader_1x02_P2.54mm_Vertical | J1 |
| 1 | CAN | PinHeader_1x05_P2.54mm_Vertical | J2 |
| 1 | 3V3 | PinHeader_1x02_P2.54mm_Vertical | J3 |
| 1 | CAN_STATUS | LED_D3.0mm | D1 |
| 1 | LOW_STATUS | LED_D3.0mm | D2 |
| 1 | UP_STATUS | LED_D3.0mm | D3 |
| 1 | RBMAS_S | LED_D3.0mm | D4 |
| 1 | CON_1 | LED_D3.0mm | D5 |
| 1 | CON_2 | LED_D3.0mm | D6 |
| 1 | STATUS | LED_D3.0mm | D7 |
| 7 | 300R | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1, R2, R3, R4, R5, R6, R7 |
ESP design files
The KiCad project lives in the nyankowan/CatchRobo_2026 repository on GitHub; these links point at the commit this page was built from.
ESP: common questions
What microcontroller does the ESP use?
The ESP is built around the ESP32_DEVKITC-32E, from the ESP32 family.
How big is the ESP PCB?
The ESP measures 48 × 65.9 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the ESP?
18 components, from 12 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the ESP design files?
From the nyankowan/CatchRobo_2026 repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the ESP design in my own project?
The repository has no license, so all rights stay with nyankowan. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the ESP without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in CatchRobo_2026
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k