Shack Relay Matrix rev C: RF board
PE1RGU·hf-antenna-switch·hardware/unit/rf-board/rf-board.kicad_pcb
About the Shack Relay Matrix rev C: RF board
Shack Relay Matrix rev C: RF board is an open source PCB design by PE1RGU, published on GitHub under the CERN-OHL-S-2.0 license. It is a 6-layer board measuring 268 × 230 mm, with 337 components from 52 distinct parts.
Other key parts include the LP2985-33DBVR, LM2901 and PCA9539PW,118. By type, the board carries 113 resistors, 55 capacitors, 54 diodes, 51 transistors, 37 relays and 14 connectors.
It belongs with the rf & radio designs in this gallery.
From the project
Remote HF antenna switch: 3 radios x 4 antennas (path to 8), outdoor relay unit with a hardware safety chain, controlled over Cat6 from a shack interface. KiCad 10, open hardware, designed together with an AI.
A remote antenna switch for an HF amateur radio station: 3 radios, 4 antennas, one Cat6 cable, and the safety rules in hardware. Designed by a radio amateur together with an AI assistant, and documented decision by decision.
The relay unit sits outdoors, close to the antennas, in a milled aluminium case. A small interface box in the shack controls it over one Cat6 cable. A computer sends the commands over USB. If anything goes wrong (a cable break, a box fault, a press on the KILL switch), every radio is inhibited and every relay is released, without help from the firmware.

Main components on the Shack Relay Matrix rev C: RF board
Shack Relay Matrix rev C: RF board bill of materials (BOM)
337 components, 52 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | LP2985-33DBVR LP2985-33 | SOT-23-5 | U1 |
| 1 | LM2901 | SOIC-14_3.9x8.7mm_P1.27mm | U801 |
| 4 | PCA9539PW,118 PCA9539 | TSSOP-24_4.4x7.8mm_P0.65mm | U901, U902, U903, U1001 |
| 1 | PMV50EPEA | SOT-23 | Q1 |
| 42 | BSS138BK | SOT-23 | Q2, Q101, Q102, Q103, Q104, Q105, Q106, Q107 +34 |
| 4 | BC857B | SOT-23 | Q1011, Q1021, Q1031, Q1041 |
| 4 | IRFL9014TRPBF IRFL9014 | SOT-223-3_TabPin2 | Q1012, Q1022, Q1032, Q1042 |
| 6 | 83-798 83-798 SO-239 | SO239_83-798_StrapPad_BossRight | J1, J2, J3, J7, J8, J9 |
| 3 | 901-9215 SMA jack EXP | SMA_901-9215_StrapPad | J4, J5, J6 |
| 1 | 83-798 83-798 SO-239 | SO239_83-798_StrapPad_BossLeft | J10 |
| 2 | XT60PW-M | AMASS_XT60PW-M_1x02_P7.20mm_Horizontal | J11, J12 |
| 1 | XT30PW-M | AMASS_XT30PW-M_1x02_P2.50mm_Horizontal | J13 |
| 1 | Controller header | PinHeader_2x12_P2.54mm_Vertical | J14 |
| 3 | 0468001.NR 1A T | Fuse_1206_3216Metric_Pad1.42x1.75mm_HandSolder | F1, F2, F3 |
| 37 | RTD14012F | Relay_SPDT_Schrack-RT1-16A-FormC_RM5mm | K101, K102, K103, K104, K105, K106, K107, K108 +29 |
| 1 | SS14 | D_SMA | D1 |
| 4 | BZT52C24 | D_SOD-123 | D2, D3, D4, D5 |
| 1 | BZT52C15 | D_SOD-123 | D6 |
| 6 | SMBJ15A | D_SMB | D7, D8, D1011, D1021, D1031, D1041 |
| 1 | SMBJ6.0A | D_SMB | D9 |
Show 32 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 37 | 1N4148W | D_SOD-123 | D101, D102, D103, D104, D105, D106, D107, D108 +29 |
| 4 | BAS70-04 | SOT-23 | D401, D501, D601, D701 |
| 4 | DNP bias choke | L_1812_4532Metric_Pad1.30x3.40mm_HandSolder | L402, L502, L602, L702 |
| 1 | DNP 10nF 1kV | C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C1 |
| 1 | DNP | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C2 |
| 6 | 1u 16V X7R | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C3, C802, C901, C902, C903, C1001 |
| 1 | 10n | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C4 |
| 1 | 4.7u 16V X7R | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C5 |
| 2 | 47u 25V polymer | CP_Elec_6.3x7.7 | C6, C7 |
| 5 | DNP bond | C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C8, C9, C10, C11, C13 |
| 1 | 10N DNP bond | C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C12 |
| 3 | 1u 50V X7R | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C101, C201, C301 |
| 4 | DNP DC block | C_1812_4532Metric_Pad1.57x3.40mm_HandSolder | C401, C501, C601, C701 |
| 4 | DNP 100n | C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C402, C502, C602, C702 |
| 4 | 10n 50V X7R | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C403, C503, C603, C703 |
| 4 | 4.7p 1kV C0G | C_1812_4532Metric_Pad1.57x3.40mm_HandSolder | C404, C504, C604, C704 |
| 4 | 47p 50V C0G | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C405, C505, C605, C705 |
| 5 | 100n | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C801, C1011, C1021, C1031, C1041 |
| 9 | DNP 100p C0G | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1201, C1202, C1203, C1204, C1205, C1206, C1207, C1208 +1 |
| 15 | 10k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R801, R811, R812, R813, R814, R831, R832 +7 |
| 3 | 2.2k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R2, R901, R902 |
| 47 | 100k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R3, R101, R102, R103, R104, R105, R106, R107 +39 |
| 1 | 0R | R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R4 |
| 4 | 1M HV | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R401, R501, R601, R701 |
| 4 | 0R wire link | WireLink_P7.62mm_D1.0mm | R402, R502, R602, R702 |
| 12 | 47k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R404, R405, R504, R505, R604, R605, R704, R705 +4 |
| 1 | 1k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R802 |
| 4 | 1M | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R821, R822, R823, R824 |
| 4 | 10R | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1011, R1021, R1031, R1041 |
| 4 | 33k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1015, R1025, R1035, R1045 |
| 9 | 0R | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1201, R1202, R1203, R1204, R1205, R1206, R1207, R1208 +1 |
| 5 | CAT16-103J4LF 10k x4 | R_Array_Convex_4x0603 | RN901, RN902, RN903, RN1001, RN1002 |
Shack Relay Matrix rev C: RF board design files
The KiCad project lives in the PE1RGU/hf-antenna-switch repository on GitHub; these links point at the commit this page was built from.
Shack Relay Matrix rev C: RF board: common questions
How big is the Shack Relay Matrix rev C: RF board?
The Shack Relay Matrix rev C: RF board measures 268 × 230 mm, has 6 copper layers and is 1.6 mm thick.
How many components are on the Shack Relay Matrix rev C: RF board?
337 components, from 52 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Shack Relay Matrix rev C: RF board design files?
From the PE1RGU/hf-antenna-switch repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Shack Relay Matrix rev C: RF board design in my own project?
Yes, under the terms of its CERN-OHL-S-2.0 license, which PE1RGU chose for the repository.
More boards in hf-antenna-switch
Similar boards
Hat
pa3gsb
65 × 56 mm81 parts2LNo license675Radioberry juice
pa3gsb
65 × 56 mm87 parts2LNo license675Radioberry preamp
pa3gsb
65 × 56 mm137 parts2LNo license675Goodwatch20
travisgoodspeed
25.6 × 27.6 mm20 parts2LNo license568GoodPocketWatch
travisgoodspeed
75.2 × 101.2 mm56 parts2LNo license568Goodwatch31
travisgoodspeed
25.6 × 27.6 mm23 parts2LNo license568