Shack Relay Matrix rev C: shack interface
PE1RGU·hf-antenna-switch·hardware/shack-interface/shack-interface.kicad_pcb
About the Shack Relay Matrix rev C: shack interface PCB
Shack Relay Matrix rev C: shack interface is an open source ESP32 PCB design by PE1RGU, published on GitHub under the CERN-OHL-S-2.0 license. It is a 4-layer board measuring 160 × 161 mm, with 265 components from 72 distinct parts.
Its main chip is the ESP32-C3-DEVKIT-RUST-1, from the ESP32 family. Other key parts include the L7805CV, LD1117S33CTR, TPS3823A-33DBVR, SN74LVC1G74DCTR and PCA9539PW,118. By type, the board carries 94 resistors, 56 capacitors, 36 diodes, 27 ICs, 19 jumpers and 13 transistors.
It belongs with the rf & radio designs in this gallery.
From the project
Remote HF antenna switch: 3 radios x 4 antennas (path to 8), outdoor relay unit with a hardware safety chain, controlled over Cat6 from a shack interface. KiCad 10, open hardware, designed together with an AI.
A remote antenna switch for an HF amateur radio station: 3 radios, 4 antennas, one Cat6 cable, and the safety rules in hardware. Designed by a radio amateur together with an AI assistant, and documented decision by decision.
The relay unit sits outdoors, close to the antennas, in a milled aluminium case. A small interface box in the shack controls it over one Cat6 cable. A computer sends the commands over USB. If anything goes wrong (a cable break, a box fault, a press on the KILL switch), every radio is inhibited and every relay is released, without help from the firmware.

Main components on the Shack Relay Matrix rev C: shack interface
Shack Relay Matrix rev C: shack interface bill of materials (BOM)
265 components, 72 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | L7805CV | TO-220-3_Vertical | U1 |
| 1 | LD1117S33CTR | SOT-223-3_TabPin2 | U2 |
| 2 | TPS3823A-33DBVR TPS3823A-33 | SOT-23-5 | U3, U6 |
| 2 | SN74LVC1G74DCTR 74LVC1G74 | SSOP-8_2.95x2.8mm_P0.65mm | U4, U9 |
| 1 | PCA9539PW,118 PCA9539 | TSSOP-24_4.4x7.8mm_P0.65mm | U5 |
| 2 | 74LVC1G14GV 74LVC1G14 | SOT-23-5 | U7, U10 |
| 7 | 74LVC1G08GV 74LVC1G08 | SOT-23-5 | U8, U201, U202, U301, U302, U401, U402 |
| 1 | 74LVC1G02GV 74LVC1G02 | SOT-23-5 | U11 |
| 1 | USBLC6-2SC6 | SOT-23-6 | U61 |
| 3 | TLP4176G | SOP-4_P2.54mm_PhotoRelay_LongPad | U203, U303, U403 |
| 3 | TLP176AM(TPL,E) TLP176AM | SOP-4_P2.54mm_PhotoRelay_LongPad | U204, U304, U404 |
| 3 | PC817X | DIP-4_W7.62mm | U205, U305, U405 |
| 1 | ESP32-C3-DEVKIT-RUST-1 ESP32-C3-DevKit-RUST-1 | ESP32-C3-DevKit-RUST_Socket | A1 |
| 4 | BCP53-16 | SOT-223-3_TabPin2 | Q11, Q21, Q31, Q41 |
| 4 | BC857B | SOT-23 | Q12, Q22, Q32, Q42 |
| 3 | BSS138BK | SOT-23 | Q13, Q23, Q33 |
| 2 | BC847B | SOT-23 | Q34, Q44 |
| 1 | 615008137121 RJ45 LINK | RJ45_8P8C_Unshielded_TabDown | J1 |
| 1 | KILL switch | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J2 |
| 1 | XT60PW-M 13.8 V IN | AMASS_XT60PW-M_1x02_P7.20mm_Horizontal | J3 |
Show 52 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | Front panel | JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J6 |
| 1 | KILL state | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J7 |
| 1 | MD-80SM R1 mini-DIN | MiniDIN-8_SameSky_MD-80SM_Horizontal | J11 |
| 1 | MD-80SM R2 mini-DIN | MiniDIN-8_SameSky_MD-80SM_Horizontal | J12 |
| 1 | MD-80SM R3 mini-DIN | MiniDIN-8_SameSky_MD-80SM_Horizontal | J13 |
| 1 | USB4105-GF-A | USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J14 |
| 1 | DISPLAY | PinHeader_1x08_P2.54mm_Vertical | J15 |
| 1 | SF-1206S050 500mA T | Fuse_1206_3216Metric | F1 |
| 4 | 2036-09-B2LF | GDT_3Pin_P4.40mm_Bourns-2036-B2_Littelfuse-SL1003A-R | GD1, GD2, GD3, GD4 |
| 1 | SDA SEL | SolderJumper-3_P1.3mm_Open_RoundedPad1.0x1.5mm_NumberLabels | JP61 |
| 3 | INH LEVEL | PinHeader_1x03_P2.54mm_Vertical | JP201, JP301, JP401 |
| 3 | PIN1 SEL | SolderJumper-3_P1.3mm_Open_RoundedPad1.0x1.5mm_NumberLabels | JP202, JP302, JP402 |
| 3 | FEED SEL | SolderJumper-3_P1.3mm_Open_RoundedPad1.0x1.5mm_NumberLabels | JP203, JP303, JP403 |
| 3 | GND BOND | SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP204, JP304, JP404 |
| 3 | SENSE A | PinHeader_1x03_P2.54mm_Vertical | JP205, JP305, JP405 |
| 3 | SENSE K | PinHeader_1x03_P2.54mm_Vertical | JP206, JP306, JP406 |
| 1 | SS34-M3/57T SS34 | D_SMC | D1 |
| 1 | SMBJ16A | D_SMB | D2 |
| 4 | SMBJ15CA | D_SMB | D11, D21, D31, D41 |
| 6 | 1N4148W | D_SOD-123 | D33, D43, D71, D201, D301, D401 |
| 3 | BZX384-C5V1 | D_SOD-323_HandSoldering | D202, D302, D402 |
| 21 | PESD15VL1BA | D_SOD-323_HandSoldering | D211, D212, D213, D214, D216, D217, D218, D311 +13 |
| 4 | ACT45B-510-2P-TL003 51u CMC | L_CMC_TDK_ACT45B | L1, L2, L3, L4 |
| 1 | 47u 35V | CP_Radial_D6.3mm_P2.50mm | C1 |
| 1 | 330n 50V X7R | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C2 |
| 2 | 100n | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C3, C71 |
| 2 | 10u 16V X7R | C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C4, C5 |
| 1 | 22u 16V X7R | C_1210_3225Metric_Pad1.33x2.70mm_HandSolder | C6 |
| 16 | 1u 16V X7R | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C7, C61, C62, C63, C72, C73, C74, C75 +8 |
| 8 | DNP 1n 1kV | C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C22, C23, C24, C25, C26, C27, C28, C29 |
| 1 | 100n 16V | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C64 |
| 3 | 10n 1kV | C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C205, C305, C405 |
| 21 | 1n C0G | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C211, C212, C213, C214, C216, C217, C218, C311 +13 |
| 2 | 0R | R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R5, R6 |
| 8 | 47R | R_MELF_MMB-0207 | R11, R12, R21, R22, R31, R32, R41, R42 |
| 4 | 220R 56R | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R13, R23, R33, R43 |
| 3 | 4.7K 22k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R14, R24, R34 |
| 9 | 100k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R15, R25, R72, R201, R202, R301, R302, R401 +1 |
| 1 | 240R 100k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R35 |
| 1 | 100K 100R | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R36 |
| 16 | 1k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R37, R47, R61, R71, R210, R211, R212, R213 +8 |
| 17 | 10k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R38, R48, R207, R214, R215, R216, R217, R307 +9 |
| 1 | 100K 22k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R44 |
| 1 | 100R | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R46 |
| 1 | 100K 1k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R62 |
| 1 | 100K 100k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R63 |
| 2 | 5k1 | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R64, R65 |
| 2 | 680R | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R73, R74 |
| 4 | 2k2 | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R75, R204, R304, R404 |
| 6 | 240R | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R203, R205, R303, R305, R403, R405 |
| 3 | 2k2 | R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R206, R306, R406 |
| 12 | DNP | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R218, R219, R220, R221, R318, R319, R320, R321 +4 |
Shack Relay Matrix rev C: shack interface design files
The KiCad project lives in the PE1RGU/hf-antenna-switch repository on GitHub; these links point at the commit this page was built from.
Shack Relay Matrix rev C: shack interface: common questions
What microcontroller does the Shack Relay Matrix rev C: shack interface use?
The Shack Relay Matrix rev C: shack interface is built around the ESP32-C3-DEVKIT-RUST-1, from the ESP32 family.
How big is the Shack Relay Matrix rev C: shack interface PCB?
The Shack Relay Matrix rev C: shack interface measures 160 × 161 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the Shack Relay Matrix rev C: shack interface?
265 components, from 72 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Shack Relay Matrix rev C: shack interface design files?
From the PE1RGU/hf-antenna-switch repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Shack Relay Matrix rev C: shack interface design in my own project?
Yes, under the terms of its CERN-OHL-S-2.0 license, which PE1RGU chose for the repository.
Can I test firmware for the Shack Relay Matrix rev C: shack interface without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in hf-antenna-switch
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k