Shack Relay Matrix rev C: controller board
PE1RGU·hf-antenna-switch·hardware/unit/controller-board/controller-board.kicad_pcb
About the Shack Relay Matrix rev C: controller board
Shack Relay Matrix rev C: controller board is an open source ESP32 PCB design by PE1RGU, published on GitHub under the CERN-OHL-S-2.0 license. It is a 4-layer board measuring 152 × 122.5 mm, with 79 components from 32 distinct parts.
Its main chip is the ESP32-C3-DEVKIT-RUST-1, from the ESP32 family. Other key parts include the VO2611, PC817X2NSZ9F, 74LVC1G14GV, TLP176AM(TPL,E) and LP2985-33DBVR. By type, the board carries 26 resistors, 20 capacitors, 12 ICs, 8 diodes, 4 inductors and 2 connectors.
It belongs with the rf & radio designs in this gallery.
From the project
Remote HF antenna switch: 3 radios x 4 antennas (path to 8), outdoor relay unit with a hardware safety chain, controlled over Cat6 from a shack interface. KiCad 10, open hardware, designed together with an AI.
A remote antenna switch for an HF amateur radio station: 3 radios, 4 antennas, one Cat6 cable, and the safety rules in hardware. Designed by a radio amateur together with an AI assistant, and documented decision by decision.
The relay unit sits outdoors, close to the antennas, in a milled aluminium case. A small interface box in the shack controls it over one Cat6 cable. A computer sends the commands over USB. If anything goes wrong (a cable break, a box fault, a press on the KILL switch), every radio is inhibited and every relay is released, without help from the firmware.

Main components on the Shack Relay Matrix rev C: controller board
Shack Relay Matrix rev C: controller board bill of materials (BOM)
79 components, 32 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 3 | VO2611 | DIP-8_W7.62mm | U1, U2, U3 |
| 1 | PC817X2NSZ9F PC817X | DIP-4_W7.62mm | U4 |
| 1 | 74LVC1G14GV 74LVC1G14 | SOT-23-5 | U5 |
| 1 | TLP176AM(TPL,E) TLP176AM | SOP-4_P2.54mm_PhotoRelay_LongPad | U6 |
| 1 | LP2985-33DBVR LP2985-33 | SOT-23-5 | U11 |
| 1 | TPS3823A-33DBVR TPS3823A-33 | SOT-23-5 | U12 |
| 1 | SN74LVC1G74DCUR 74LVC1G74 | VSSOP-8_2.3x2mm_P0.5mm | U13 |
| 1 | SN74LVC1G27DBVR 74LVC1G27 | SOT-23-6 | U14 |
| 1 | 74LVC1G02GV 74LVC1G02 | SOT-23-5 | U15 |
| 1 | 74LVC1G08GV 74LVC1G08 | SOT-23-5 | U16 |
| 1 | ESP32-C3-DEVKIT-RUST-1 ESP32-C3-DevKit-RUST-1 | ESP32-C3-DevKit-RUST_Socket | A1 |
| 1 | BSS138BK | SOT-23 | Q4 |
| 1 | 615008137121 RJ45 LINK | RJ45_8P8C_Unshielded_TabDown | J1 |
| 1 | ESQ-112-33-G-D to RF board J14 | PinSocket_2x12_P2.54mm_Vertical | J2 |
| 4 | 2036-09-B2LF | GDT_3Pin_P4.40mm_Bourns-2036-B2_Littelfuse-SL1003A-R | GD1, GD2, GD3, GD4 |
| 1 | SDA SEL | SolderJumper-3_P1.3mm_Open_RoundedPad1.0x1.5mm_NumberLabels | JP11 |
| 4 | SMBJ15CA | D_SMB | D11, D21, D31, D41 |
| 4 | 1N4148W | D_SOD-123 | D12, D22, D32, D42 |
| 4 | ACT45B-510-2P-TL003 51u CMC | L_CMC_TDK_ACT45B | L1, L2, L3, L4 |
| 10 | 1u 16V X7R | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1, C2, C3, C4, C5, C11, C14, C15 +2 |
Show 12 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 10N 10n | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C12 |
| 1 | 4.7u 16V X7R | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C13 |
| 8 | DNP 1n 1kV | C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C21, C22, C23, C24, C25, C26, C27, C28 |
| 8 | 47R | R_MELF_MMB-0207 | R11, R12, R21, R22, R31, R32, R41, R42 |
| 3 | 220R | R_MiniMELF_MMA-0204 | R13, R23, R33 |
| 3 | 4.7K 4.7k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R14, R24, R34 |
| 1 | 240R | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R35 |
| 4 | 100K 100k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R36, R44, R62, R63 |
| 1 | 220R | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R43 |
| 4 | 0R | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R51, R52, R53, R64 |
| 1 | 1k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R61 |
| 1 | 0R | R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R65 |
Shack Relay Matrix rev C: controller board design files
The KiCad project lives in the PE1RGU/hf-antenna-switch repository on GitHub; these links point at the commit this page was built from.
Shack Relay Matrix rev C: controller board: common questions
What microcontroller does the Shack Relay Matrix rev C: controller board use?
The Shack Relay Matrix rev C: controller board is built around the ESP32-C3-DEVKIT-RUST-1, from the ESP32 family.
How big is the Shack Relay Matrix rev C: controller board?
The Shack Relay Matrix rev C: controller board measures 152 × 122.5 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the Shack Relay Matrix rev C: controller board?
79 components, from 32 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Shack Relay Matrix rev C: controller board design files?
From the PE1RGU/hf-antenna-switch repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Shack Relay Matrix rev C: controller board design in my own project?
Yes, under the terms of its CERN-OHL-S-2.0 license, which PE1RGU chose for the repository.
Can I test firmware for the Shack Relay Matrix rev C: controller board without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in hf-antenna-switch
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k