Drone
PlumPot55·PCB_Designs·Drone_PCB/Drone_PCB.kicad_pcb
About the Drone PCB
Drone is an open source ESP32 PCB design by PlumPot55, published on GitHub. It is a 2-layer board measuring 36.2 × 36.2 mm, with 42 components from 19 distinct parts.
Its main chip is the ESP32-WROOM-32, from the ESP32 family. Other key parts include the CP2104, SI2302-TP, MIC5219-3.3YMM and MPU-6050. By type, the board carries 15 resistors, 10 capacitors, 8 ICs, 4 diodes, 2 transistors and 2 connectors.
It belongs with the robotics & motion designs in this gallery.
From the project
Source Files of our PCB we did as a community
Main components on the Drone
Drone bill of materials (BOM)
42 components, 19 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-WROOM-32 | ESP32-WROOM-32 | U1 |
| 1 | CP2104 | QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm | U2 |
| 4 | SI2302-TP | SOT-23 | U3, U5, U8, U9 |
| 1 | MIC5219-3.3YMM | MSOP-8_3x3mm_P0.65mm | U4 |
| 1 | MPU-6050 | InvenSense_QFN-24_4x4mm_P0.5mm | U6 |
| 2 | TRANS_NPN-MMBT2222AL | SOT23-3 | Q1, Q2 |
| 1 | USB_B_Mini | USB_Micro-B_Molex_47346-0001 | J5 |
| 1 | CONN_01X02 Conn_01x02 | PinHeader_1x02_P2.54mm_Vertical | J9 |
| 1 | MOMENTARY-SWITCH-SPST-2-SMD-4.6X2.8MM | TACTILE_SWITCH_SMD_4.6X2.8MM | S1 |
| 4 | D_Schottky | D_2114_3652Metric_Pad1.85x3.75mm_HandSolder | D2, D3, D4, D5 |
| 4 | 10UF 10uF | C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C1, C2, C8, C10 |
| 4 | 0.1UF 0.1uF | C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C3, C9, C11, C12 |
| 1 | 4.7UF 4.7uF | C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C7 |
| 1 | 2.2NF 2.2nF | C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C13 |
| 6 | 10K | R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R3, R4, R12, R13, R14, R15 |
| 3 | 100R | R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R5, R6, R7 |
| 2 | 100K | R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R8, R9 |
| 2 | 2K2 2k2 | R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R10, R11 |
| 2 | 0R | R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R16, R17 |
Drone design files
The KiCad project lives in the PlumPot55/PCB_Designs repository on GitHub; these links point at the commit this page was built from.
Drone: common questions
What microcontroller does the Drone use?
The Drone is built around the ESP32-WROOM-32, from the ESP32 family.
How big is the Drone PCB?
The Drone measures 36.2 × 36.2 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Drone?
42 components, from 19 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Drone design files?
From the PlumPot55/PCB_Designs repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.
Can I use the Drone design in my own project?
The repository has no license, so all rights stay with PlumPot55. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Drone without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in PCB_Designs
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k