HardLabs

Route import.tmp

PNT2110·FC_ESP32·FC_ESP32/route_import.tmp.kicad_pcb

Route import.tmp PCB layout, top view — open source ESP32 board by PNT2110

About the Route import.tmp PCB

Route import.tmp is an open source ESP32 PCB design by PNT2110, published on GitHub. It is a 2-layer board measuring 79.8 × 79.8 mm, with 72 components from 38 distinct parts.

Its main chip is the ESP32-WROOM-32 (8MB), from the ESP32 family. Other key parts include the MPU-6500, CH340C, USBLC6-2SC6, TPS63001DRCR and TPS61070DDCR. By type, the board carries 23 resistors, 20 capacitors, 9 connectors, 6 ICs, 6 transistors and 6 diodes.

It belongs with the robotics & motion, power & battery and sensors designs in this gallery.

From the project

An ESP32-WROOM-32 based flight controller designed for 1S brushed quadcopters.

An ESP32-WROOM-32 based flight controller designed for 1S brushed quadcopters.

The subsequent datasheet review found B.Cu tracks inside the ESP32 antenna region, power-layout concerns and incomplete flight features despite clean ERC/DRC. See BAOCAOKIEMTRAMACH.md and validation/datasheetaudit/LOGKIEMTRA.md`. The independent antenna check fails; do not interpret the routing checks below as proof that the design is ready to operate or manufacture.

Main components on the Route import.tmp

ESP32-WROOM-32 (8MB)MPU-6500CH340CUSBLC6-2SC6TPS63001DRCRTPS61070DDCR

Route import.tmp bill of materials (BOM)

72 components, 38 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
ESP32-WROOM-32 (8MB)
U1
1
MPU-6500
U2
1
CH340C
U3
1
USBLC6-2SC6
U4
1
TPS63001DRCR
U5
1
TPS61070DDCR
U6
4
AO3400
Q1, Q2, Q3, Q4
2
MMBT3904
Q5, Q6
1
USB4105-GF-A
J1
1
MTF-01P SH1.0
J2
1
BAT 1S
J3
1
M1 + / -
J4
1
M2 + / -
J5
1
M3 + / -
J6
1
M4 + / -
J7
1
I2C
J8
1
UART1
J9
6
SS16
D1, D2, D3, D4, D5, D6
1
2.2uH VLF4012-2R2M1R5
L1
1
4.7uH >=1A shielded
L2
Show 18 more
QtyPartRefs
2
22uF 10V X5R
C1, C17
7
100NF
100nF
C2, C4, C5, C7, C9, C15, C18
1
1UF
1uF
C3
1
10NF
10nF
C6
1
1UF
1uF
C8
1
1uF 10V
C11
2
10uF 10V X5R
C12, C13
1
47uF 10V X5R
C19
4
100nF 10V
C21, C22, C23, C24
5
10K
10k
R1, R2, R6, R9, R10
2
100k 1%
R3, R4
1
10R
R5
2
5.1k 1%
R7, R8
5
100R
R11, R15, R17, R19, R21
1
1.8M 1%
R12
1
200k 1%
R13
4
100K
100k
R16, R18, R20, R22
2
4.7K
4.7k
R23, R24

Route import.tmp design files

The KiCad project lives in the PNT2110/FC_ESP32 repository on GitHub; these links point at the commit this page was built from.

Route import.tmp: common questions

What microcontroller does the Route import.tmp use?

The Route import.tmp is built around the ESP32-WROOM-32 (8MB), from the ESP32 family.

How big is the Route import.tmp PCB?

The Route import.tmp measures 79.8 × 79.8 mm, has 2 copper layers and is 0.8 mm thick.

How many components are on the Route import.tmp?

72 components, from 38 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Route import.tmp design files?

From the PNT2110/FC_ESP32 repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.

Can I use the Route import.tmp design in my own project?

The repository has no license, so all rights stay with PNT2110. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Route import.tmp without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

More boards in FC_ESP32

Similar boards