Connected heart
ppedropimenta·connected-heart·hardware/kicad/connected-heart-carrier.kicad_sch
About the Connected heart PCB
Connected heart is an open source ESP32 PCB design by ppedropimenta, published on GitHub. It is a board, with 13 components from 10 distinct parts.
Its main chip is the ESP32-C3 SuperMini, from the ESP32 family. Other key parts include the 74AHCT1G125. By type, the board carries 6 capacitors, 3 connectors, 2 ICs, 1 switch and 1 resistor.
It belongs with the displays & leds and dev boards & breakouts designs in this gallery.
From the project
Receive-only e-paper messaging device: ESP32-C3 firmware, custom KiCad carrier board, 3D-printed enclosure
KiCad 10. Only the schematic is published; preview/ has the schematic as PDF and renders of the board.
- ERC: no errors or warnings - DRC with schematic parity: no violations, nothing unconnected - Netlist checked against the pin map in firmware/src/Core/Pins.h
2-layer, 1.6 mm, 70 × 40 mm, four mounting holes.
- The SuperMini is soldered by its castellated edges, with through-holes under each pin so pin headers would also fit. Its USB-C end sticks out about 1 mm over the back edge. - No copper on either layer under the SuperMini's antenna. - C1 and C2 sit next to the SuperMini's power…
Main components on the Connected heart
Connected heart bill of materials (BOM)
13 components, 10 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-C3 SuperMini | ESP32-C3_SuperMini | U1 |
| 1 | 74AHCT1G125 | SOT-23-5 | U2 |
| 1 | TOUCH | JST_PH_B3B-PH-K_1x03_P2.00mm_Vertical | J1 |
| 1 | LED | JST_PH_B3B-PH-K_1x03_P2.00mm_Vertical | J2 |
| 1 | EPD | Molex_PicoBlade_53047-0810_1x08_P1.25mm_Vertical | J3 |
| 1 | RESET | SW_SPST_EVQP7A | SW1 |
| 1 | 220u 6.3V | CP_Elec_6.3x5.8 | C1 |
| 2 | 10u | C_0805_2012Metric | C2, C4 |
| 3 | 100n | C_0603_1608Metric | C3, C5, C6 |
| 1 | 330 | R_0603_1608Metric | R1 |
Connected heart design files
The KiCad project lives in the ppedropimenta/connected-heart repository on GitHub; these links point at the commit this page was built from.
Connected heart: common questions
What microcontroller does the Connected heart use?
The Connected heart is built around the ESP32-C3 SuperMini, from the ESP32 family.
How many components are on the Connected heart?
13 components, from 10 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Connected heart design files?
From the ppedropimenta/connected-heart repository on GitHub, which has the schematic and the BOM; the links under Design files point to each one.
Can I use the Connected heart design in my own project?
The repository has no license, so all rights stay with ppedropimenta. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Connected heart without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k