Smart park design
RAJ-IITROORKEE·smart-park-design·hardware/SmartMark.kicad_pcb
About the Smart park design PCB
Smart park design is an open source ESP32 PCB design by RAJ-IITROORKEE, published on GitHub. It is a 2-layer board measuring 62 × 50 mm, with 24 components from 20 distinct parts.
Its main chip is the XIAO ESP32-S3, from the ESP32 family. Other key parts include the TPS61099DRVR, SN74LVC1T45DBVR and SN74LVC1G17DBVR. By type, the board carries 9 resistors, 7 capacitors, 4 ICs, 2 connectors, 1 diode and 1 inductor.
It belongs with the rf & radio, displays & leds and power & battery designs in this gallery.
From the project
SmartPark RevD indoor parking node: XIAO ESP32S3 and Wio-SX1262 carrier PCB, HC-SR04, snap-fit enclosures, CAD previews, fabrication files and build guides.
XIAO ESP32S3 · Wio-SX1262 LoRa · HC-SR04 · LiPo · optional OLED
Rev D indoor pilot — digitally checked, awaiting physical validation
Download PCB · Download case · Build guide · 3D models
SmartPark is a hardware design for an indoor parking-bay occupancy node. Mount it above the bay with the ultrasonic faces pointing down; parking firmware can compare the measured distance with an empty-bay baseline and report changes over LoRa. The target installation height is up to 2.8 m.

Main components on the Smart park design
Smart park design bill of materials (BOM)
24 components, 20 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | XIAO ESP32-S3 | XIAO_S3_STACK_SOCKET_2x7 | U1 |
| 1 | TPS61099DRVR | WSON-6-1EP_2x2mm_P0.65mm_EP1x1.6mm | U2 |
| 1 | SN74LVC1T45DBVR | SOT-23-6 | U3 |
| 1 | SN74LVC1G17DBVR | SOT-23-5 | U4 |
| 1 | HC-SR04 5V | JST_PH_B4B-PH-K_1x04_P2.00mm_Vertical | J1 |
| 1 | 0.96in OLED | PinHeader_1x04_P2.54mm_Vertical | J2 |
| 1 | WS2812B-2020-V6 | WS2812B_2020_V6 | D1 |
| 1 | 2.2UH 2.2uH | VLS3012CX_2R2M | L1 |
| 1 | 10uF 10V X7R | C_0805_2012Metric | C1 |
| 2 | 22uF 16V X7R | C_1206_3216Metric | C2, C3 |
| 4 | 100NF 100nF | C_0603_1608Metric | C4, C5, C6, C7 |
| 1 | 1M | R_0603_1608Metric | R1 |
| 1 | 249K 249k | R_0603_1608Metric | R2 |
| 1 | 100k EN pulldown | R_0603_1608Metric | R3 |
| 1 | 100k HC_ECHO pulldown | R_0603_1608Metric | R4 |
| 1 | 330R LED series | R_0603_1608Metric | R5 |
| 1 | 100k LED_DIN pulldown | R_0603_1608Metric | R6 |
| 1 | 100k LED_DATA pulldown | R_0603_1608Metric | R7 |
| 1 | 4.7k SDA pullup | R_0603_1608Metric | R8 |
| 1 | 4.7k SCL pullup | R_0603_1608Metric | R9 |
Smart park design design files
The KiCad project lives in the RAJ-IITROORKEE/smart-park-design repository on GitHub; these links point at the commit this page was built from.
- Layouthardware/SmartMark.kicad_pcb
- Schematichardware/SmartMark.kicad_sch
- BOMoutputs/BOM.csv
Smart park design: common questions
What microcontroller does the Smart park design use?
The Smart park design is built around the XIAO ESP32-S3, from the ESP32 family.
How big is the Smart park design PCB?
The Smart park design measures 62 × 50 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Smart park design?
24 components, from 20 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Smart park design design files?
From the RAJ-IITROORKEE/smart-park-design repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Smart park design design in my own project?
The repository has no license, so all rights stay with RAJ-IITROORKEE. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Smart park design without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k