FireLord Device
RatKinng·FireLord·pcb-and-schematics/FireLord_Sensor_Device/FireLord_Device/FireLord_Device.kicad_pcb
About the FireLord Device PCB
FireLord Device is an open source Microchip SAM PCB design by RatKinng, published on GitHub. It is a 2-layer board measuring 105.4 × 50.8 mm, with 10 components from 8 distinct parts.
Its main chip is the XIAO-SAMD21-SMD, from the Microchip SAM family. Other key parts include the SCD40-D-R2, LM2937xMP, MPL3115A2 and MIC5205-2.7YM5.
It belongs with the rf & radio, sensors and power & battery designs in this gallery.
From the project
The KiCad project in this directory defines the sensor carrier board used by FireLord. It is suitable for small fabrication runs and straightforward to adapt for alternate sensors or power stages.
The KiCad project in this directory defines the sensor carrier board used by FireLord. It is suitable for small fabrication runs and straightforward to adapt for alternate sensors or power stages.
Open the .kicadpro file in KiCad 7+. If footprints appear missing, point KiCad to the bundled PressureSensor.pretty` library.
- Seeeduino XIAO header exposing I²C, UART, analog, and power rails. - JST or locking connectors for CO, smoke, VOC, and other sensor daughterboards. - SCD40 and MPL115A2 wired on a shared I²C bus with 400 kHz pull-ups. - Supercapacitor pads with balancing resistors and…
Main components on the FireLord Device
FireLord Device bill of materials (BOM)
10 components, 8 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | SCD40-D-R2 | Sensirion_SCD4x-1EP_10.1x10.1mm_P1.25mm_EP4.8x4.8mm | U1 |
| 1 | XIAO-SAMD21-SMD | XIAO-SAMD21-SMD | U2 |
| 1 | LM2937xMP | SOT-223-3_TabPin2 | U3 |
| 1 | MPL3115A2 | NXP_LGA-8_3x5mm_P1.25mm_H1.1mm | U4 |
| 1 | MIC5205-2.7YM5 | SOT-23-5 | U6 |
| 1 | Conn_01x04_Socket | JST_EH_B4B-EH-A_1x04_P2.50mm_Vertical | Lora1 |
| 2 | Conn_01x03_Socket | FanPinHeader_1x03_P2.54mm_Vertical | Smoke1, VOC1 |
| 2 | Conn_01x02_Socket | JST_XA_B02B-XASK-1-A_1x02_P2.50mm_Vertical | Solar Panel1, Super Cap1 |
FireLord Device design files
The KiCad project lives in the RatKinng/FireLord repository on GitHub; these links point at the commit this page was built from.
FireLord Device: common questions
What microcontroller does the FireLord Device use?
The FireLord Device is built around the XIAO-SAMD21-SMD, from the Microchip SAM family.
How big is the FireLord Device PCB?
The FireLord Device measures 105.4 × 50.8 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the FireLord Device?
10 components, from 8 distinct parts. The full bill of materials is listed on this page.
Where can I download the FireLord Device design files?
From the RatKinng/FireLord repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the FireLord Device design in my own project?
The repository has no license, so all rights stay with RatKinng. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the FireLord Device without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug Microchip SAM firmware against it before you order a PCB.
More boards in FireLord
Similar boards
Microchip SAM
Microcontroller Expansion Card
FrameworkComputer
26 × 30 mm24 parts2LCC-BY-4.01.1kMicrochip SAM
Taco Raven
VoronDesign
120 × 113 mm349 parts4LGPL-3.01.1kMicrochip SAM
Fpgaboy
Wren6991
50 × 50 mm89 parts4LNo license511Microchip SAM
OpenDropV4
GaudiLabs
124 × 115.4 mm118 parts2LGPL-3.0487Microchip SAM
ModulAdapter universal
GaudiLabs
100 × 69.5 mm45 parts2LGPL-3.0487Microchip SAM
Kira
kiibohd
366.9 × 114.3 mm400 partsCERN-OHL-1.2416