27 open source boards using the MPL3115A2
Real designs built with the MPL3115A2, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Avionics-Board
ModelRocketryAvionics
30 × 55 mm66 parts3LNo license8FPGA
Keep breathing ctrl
CV19CO
153 × 148 mm248 parts4LCERN-OHL-P-2.05RP2040/RP2350
Odyssey
MeghanaM4
20.9 × 26 mm7 parts2LMIT4STM32
Rocket
scottzach1
121.9 × 74.9 mm7 parts2LMIT3BenTo-Legacy
benkuper
142 × 23 mm76 parts2LGPL-3.01PiADC2
capconix
65 × 56 mm70 parts2LNo license1AVR/Arduino
AAQuad-Evolution
Fberbari
55.6 × 48.8 mm43 parts2LMIT1RP2040/RP2350
Linux Version Purple
raybello
67.6 × 49.5 mm295 parts4LNo license0PIC
PTR arecorder
PTR-projects
74 × 25 mm83 parts2LMIT0Raspberry Pi
USLI Payload Motherboard
Rose-Rocketry
109.2 × 50.8 mm78 parts2LMIT0NXP
YIPPEE Software
mpkarpov-ui
21.2 × 82.8 mm22 parts2LNo license0Microchip SAM
FireLord Device
RatKinng
105.4 × 50.8 mm10 parts2LNo license0RP2040/RP2350
Insight
K-Eckert15
69.9 × 26 mm72 parts4LNo license1Microchip SAM
Avionics Board 1
djmallek
50 × 50 mm63 parts2LNo license1Pressure sensors
CV19CO
100 × 100 mm10 parts4LCERN-OHL-P-2.05RP2040/RP2350
COMET: Compact Onboard Management for Ejectio Timing
K-Eckert15
63.5 × 25.4 mm68 parts4LNo license1Microchip SAM
CircularM0 - AvionicsProcessor
djmallek
88.9 × 88.9 mm56 parts2LNo license1RP2040/RP2350
CM4IOv5
raybello
160 × 90 mm137 parts4LNo license0NXP
Rev1
Olin-Rocketry
83.8 × 94 mm43 parts2LNo license0ESP32
Flight computer
Helios-Rocket
25.5 × 51.5 mm36 parts4LNo license1NXP
Rev2
Olin-Rocketry
72 × 80 mm34 parts2LNo license0ADCS
skycan
50 × 50 mm29 parts2LCustom license0RP2040/RP2350
PiUAV
raybello
30 × 65 mm67 parts4LNo license0AVR/Arduino
Elevator altimeter
reivax-boucoi
100 × 55 mm40 parts2LNo license1ESP32
Radio Board Rev2
Olin-Rocketry
100 × 65.5 mm16 parts2LNo license0NXP
BMI088
Olin-Rocketry
29.2 × 18 mm13 parts2LNo license0BNO055 circuit i2C version 3
Olin-Rocketry
13.8 × 13.3 mm13 parts2LNo license0
How designs wire the MPL3115A2
Read from the KiCad layouts of 18 open source designs, one per repository: what each pin of the MPL3115A2 connects to, and the resistors, capacitors and other passives placed on it.
- The CAP pin has a capacitor to GND on 13 of 18 designs, most often 100 nF.
- The VDD pin has a decoupling capacitor on 12 of 18 designs, most often 100 nF (then 10 µF).
- The VDDIO pin has a decoupling capacitor on 12 of 18 designs, most often 100 nF (then 10 µF).
- The INT2 pin is left unconnected on 11 of 18 designs (a signal on 6).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VDDpin 1 | Connected to: 3.3V 67% · a signal 33% |
|
| CAPpin 2 | Connected to: Signal 83% · not connected 17% |
|
| GNDpin 3 | Connected to: GND 78% · a signal 17% | — |
| VDDIOpin 4 | Connected to: 3.3V 61% · a signal 28% |
|
| INT2pin 5 | Connected to: Not connected 61% · a signal 33% | — |
| SDLpin 7 | Connected to: The microcontroller 50%, a connector 22% |
|
| SCLpin 8 | Connected to: The microcontroller 56%, a connector 22% |
|
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Avionics-Board by ModelRocketryAvionics, Keep breathing ctrl by CV19CO, Odyssey by MeghanaM4 and RocketPCB by scottzach1.
The MPL3115A2 in open source designs
The gallery holds 27 open source boards using the MPL3115A2 from 18 GitHub repositories; a typical one measures about 69.8 × 51.5 mm and carries around 43 components.
67% are two-layer designs, the rest use four layers or more, and 30% carry an open source license.
The most starred is Avionics-Board by ModelRocketryAvionics.
Parts used alongside the MPL3115A2
Microcontrollers on boards using the MPL3115A2
What boards using the MPL3115A2 are built for
MPL3115A2: common questions
Where can I find a MPL3115A2 reference design?
Each of the 27 boards on this page is a real design using the MPL3115A2. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the MPL3115A2 CAP pin connected?
The CAP pin has a capacitor to GND on 13 of 18 designs, most often 100 nF. Counted from the KiCad layouts of 18 open source designs using the MPL3115A2.
What decoupling capacitors do designs use on the MPL3115A2 VDD pin?
The VDD pin has a decoupling capacitor on 12 of 18 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 18 open source designs using the MPL3115A2.
What decoupling capacitors do designs use on the MPL3115A2 VDDIO pin?
The VDDIO pin has a decoupling capacitor on 12 of 18 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 18 open source designs using the MPL3115A2.
What parts are used alongside the MPL3115A2?
The BNO055, IIS2MDCTR, MCP73831, MPU-6050 and RP2040 appear in the most repositories here.
Which microcontrollers do boards using the MPL3115A2 use?
Most are built on RP2040/RP2350 (6), NXP (4), Microchip SAM (3) and AVR/Arduino (2).
How big is a typical board using the MPL3115A2?
The median is 69.8 × 51.5 mm, and 67% are two-layer designs.
What is the most popular open source board using the MPL3115A2?
By GitHub stars, Avionics-Board by ModelRocketryAvionics, with 8 stars.
Can I simulate one of these boards using the MPL3115A2 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.