Can modbus tap
reliablereefs·can-modbus-tap·hardware/kicad/can-modbus-tap.kicad_pcb
About the Can modbus tap PCB
Can modbus tap is an open source ESP32 PCB design by reliablereefs, published on GitHub. It is a 2-layer board measuring 90 × 66 mm, with 40 components from 28 distinct parts.
Its main chip is the ESP32-S3-WROOM-1-N8, from the ESP32 family. Other key parts include the ISO1042, ISO1640BD, ADS1115IDGSR, RFM-0505S and AP7361C-33E-13. By type, the board carries 15 resistors, 9 capacitors, 7 ICs, 3 diodes, 2 connectors and 2 switches.
It belongs with the iot & wireless designs in this gallery.
From the project
Spy on hardware interactions
Listen-only probe for a 24 V accessory port that uses a USB-A shell. An ESP32-S3 records classic CAN frames, a collector stores them, and MODBUS RTU payloads inside those frames are decoded into request/response pairs and a register map.
The probe cannot transmit. The isolated CAN transceiver's TXD pin is tied to its logic supply, so the driver stays recessive, and the ESP32 TWAI controller runs in listen-only mode. Use it on equipment you are allowed to monitor.
Main components on the Can modbus tap
Can modbus tap bill of materials (BOM)
40 components, 28 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-WROOM-1-N8 Espressif | ESP32-S3-WROOM-1 | U1 |
| 1 | ISO1042 ISO1042BDW Texas Instruments | SOIC-16W_7.5x10.3mm_P1.27mm | U2 |
| 1 | ISO1640BD Texas Instruments | SOIC-8_3.9x4.9mm_P1.27mm | U3 |
| 1 | ADS1115IDGSR Texas Instruments | MSOP-10_3x3mm_P0.5mm | U4 |
| 1 | RFM-0505S RECOM | RECOM_RFM-0505S | U5 |
| 1 | AP7361C-33E-13 Diodes Inc | SOT-223-3_TabPin2 | U6 |
| 1 | AP2112K-3.3 Diodes Inc | SOT-23-5 | U7 |
| 1 | USB-A plug Würth | USB3_A_Plug_Wuerth_692112030100_Horizontal | J1 |
| 1 | USB-C GCT | USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J2 |
| 1 | TERM | PinHeader_1x02_P2.54mm_Vertical | JP1 |
| 1 | BOOT | SW_PUSH_6mm | SW1 |
| 1 | RESET | SW_PUSH_6mm | SW2 |
| 1 | NUP2105LT1G onsemi | SOT-23 | D1 |
| 1 | BZT52C3V6 Nexperia | D_SOD-123 | D2 |
| 1 | LED | LED_0603_1608Metric | D3 |
| 1 | ACT45B-510-2P TDK | ACT45B-510-2P | L1 |
| 3 | 10uF | C_0805_2012Metric | C1, C6, C7 |
| 5 | 100NF 100nF | C_0402_1005Metric | C2, C3, C4, C5, C8 |
| 1 | 1UF 1uF | C_0402_1005Metric | C9 |
| 1 | 91.0k | R_0603_1608Metric | R1 |
Show 8 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 12.0k | R_0603_1608Metric | R2 |
| 1 | 1k | R_0603_1608Metric | R3 |
| 4 | 4.7K 4.7k | R_0603_1608Metric | R4, R5, R6, R7 |
| 2 | 5.1K 5.1k | R_0603_1608Metric | R8, R9 |
| 2 | 10K 10k | R_0603_1608Metric | R10, R11 |
| 1 | 330 | R_0603_1608Metric | R12 |
| 1 | 120 | R_0603_1608Metric | R13 |
| 2 | 22 | R_0603_1608Metric | R14, R15 |
Can modbus tap design files
The KiCad project lives in the reliablereefs/can-modbus-tap repository on GitHub; these links point at the commit this page was built from.
Can modbus tap: common questions
What microcontroller does the Can modbus tap use?
The Can modbus tap is built around the ESP32-S3-WROOM-1-N8, from the ESP32 family.
How big is the Can modbus tap PCB?
The Can modbus tap measures 90 × 66 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Can modbus tap?
40 components, from 28 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Can modbus tap design files?
From the reliablereefs/can-modbus-tap repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Can modbus tap design in my own project?
The repository has no license, so all rights stay with reliablereefs. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Can modbus tap without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k