84 open source boards using the ADS1115IDGSR

Real designs built with the ADS1115IDGSR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

84 boardsClear filters|Most starred

How designs wire the ADS1115IDGSR

Read from the KiCad layouts of 63 open source designs, one per repository: what each pin of the ADS1115IDGSR connects to, and the resistors, capacitors and other passives placed on it.

  • The VDD pin has a decoupling capacitor on 47 of 63 designs, most often 100 nF (then 1 µF).
  • The SDA pin has a pull-up to 3.3V on 46 of 63 designs, most often 4.7 kΩ (then 10 kΩ).
  • The SCL pin has a pull-up to 3.3V on 46 of 63 designs, most often 4.7 kΩ (then 10 kΩ).
  • The ADDR pin is tied to GND on 46 of 63 designs (a signal on 16).
ADDRpin 1Connected to: GND 73% · a signal 25%
ALERT/RDYpin 2Connected to: Not connected 57% · a signal 43%
  • Pull-up to 3.3V on 30% · 10 kΩ (15), 4.7 kΩ (2)
GNDpin 3Connected to: GND 95%
AIN0pin 4Connected to: A connector 22%
  • Series resistor on 59% · 1 kΩ (10), 10 kΩ (8), 470 Ω (2)
  • Capacitor to GND on 49% · 100 nF (19), 10 nF (3), 1 µF (2)
AIN1pin 5Connected to: A connector 25%
  • Series resistor on 51% · 1 kΩ (8), 10 kΩ (7), 470 Ω (2)
  • Capacitor to GND on 44% · 100 nF (18), 2.2 µF (1), 33 nF (1)
AIN2pin 6Connected to: A connector 21%
  • Series resistor on 40% · 10 kΩ (7), 1 kΩ (6), 240 Ω (2)
  • Capacitor to GND on 37% · 100 nF (15), 10 nF (3), 1 nF (1)
AIN3pin 7Connected to: A connector 24% · GND 17%
  • Series resistor on 37% · 10 kΩ (5), 1 kΩ (5), 240 Ω (2)
  • Capacitor to GND on 30% · 100 nF (16), 1 nF (1), 3.3 µF (1)
VDDpin 8Connected to: 3.3V 84% · a signal 16%
  • Decoupling capacitor on 75% · 100 nF (57), 1 µF (10), 10 µF (7)
SDApin 9Connected to: The microcontroller 43%, a connector 41%
  • Pull-up to 3.3V on 73% · 4.7 kΩ (23), 10 kΩ (20), 2.2 kΩ (5)
SCLpin 10Connected to: The microcontroller 43%, a connector 41%
  • Pull-up to 3.3V on 73% · 4.7 kΩ (23), 10 kΩ (20), 2.2 kΩ (5)

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include USMU by joeltroughton, Zynaptik Circuit by zynthian, Moss by metrox-eth and Cm4 motherboard by Twisted-Fields.

The ADS1115IDGSR in open source designs

The gallery holds 84 open source boards using the ADS1115IDGSR from 69 GitHub repositories; a typical one measures about 82 × 57.5 mm and carries around 78 components.

62% use four copper layers or more, and 44% carry an open source license.

The most starred is USMU by joeltroughton.

Microcontrollers on boards using the ADS1115IDGSR

ADS1115IDGSR: common questions

Where can I find a ADS1115IDGSR reference design?

Each of the 84 boards on this page is a real design using the ADS1115IDGSR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What decoupling capacitors do designs use on the ADS1115IDGSR VDD pin?

The VDD pin has a decoupling capacitor on 47 of 63 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 63 open source designs using the ADS1115IDGSR.

What pull-up resistor is used on the ADS1115IDGSR SDA pin?

The SDA pin has a pull-up to 3.3V on 46 of 63 designs, most often 4.7 kΩ (then 10 kΩ). Counted from the KiCad layouts of 63 open source designs using the ADS1115IDGSR.

What pull-up resistor is used on the ADS1115IDGSR SCL pin?

The SCL pin has a pull-up to 3.3V on 46 of 63 designs, most often 4.7 kΩ (then 10 kΩ). Counted from the KiCad layouts of 63 open source designs using the ADS1115IDGSR.

What parts are used alongside the ADS1115IDGSR?

The USBLC6-2SC6, AMS1117-3.3, AP2112K-3.3, AP2112K-3.3TRG1 and ESP32-S3-WROOM-1-N16R8 appear in the most repositories here.

Which microcontrollers do boards using the ADS1115IDGSR use?

Most are built on ESP32 (24), RP2040/RP2350 (8), STM32 (8) and Raspberry Pi (5).

How big is a typical board using the ADS1115IDGSR?

The median is 82 × 57.5 mm, and 38% are two-layer designs.

What is the most popular open source board using the ADS1115IDGSR?

By GitHub stars, USMU by joeltroughton, with 156 stars.

Can I simulate one of these boards using the ADS1115IDGSR before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part