Relay24 ESP32
renatorgr·Boards·Relay24_ESP32/Relay24_ESP32.kicad_pcb
About the Relay24 ESP32 PCB
Relay24 ESP32 is an open source PCB design by renatorgr, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 210 × 120 mm, with 158 components from 62 distinct parts.
Other key parts include the 74HC595, ULN2803A, LM2596S-5.0, AMS1117-3.3 and RTL8201F. By type, the board carries 41 resistors, 34 connectors, 31 diodes, 24 relays, 17 capacitors and 9 ICs.
It belongs with the iot & wireless, rf & radio and power & battery designs in this gallery.
From the project
Hardware and firmware for the AgOpenGPS AiO v4.5 autosteer boards: Teensy 4.1 firmware with its own web page (GPS, IMU, autosteer), a XIAO ESP32 Wi-Fi status page, XIAO adapter boards, and an Arduino Nano sprayer section controller. Works with AgOpenWeb and AgOpenGPS.
A 210 x 120 mm two-layer board that holds everything needed to drive 24 sections with 12 V linear actuators from AgOpenGPS / AgOpenWeb (machine module over UDP):
- an ESP32 DevKitC V4 (38 pins) plugged into two 1x19 sockets, running SeederESP32 or SprayerESP32 with a board profile for this hardware (see Firmware below); - three 74HC595 shift registers + three ULN2803A driving 24 DPDT relays (HF115F/012-2ZS4, 8 A); each relay reverses one actuator: relay off = actuator pulled in (section closed), relay on = actuator pushed out (section open); a green LED per section; - RTL8201F + RJ45 (RMII…

Main components on the Relay24 ESP32
Relay24 ESP32 bill of materials (BOM)
158 components, 62 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 3 | 74HC595 | SOIC-16_3.9x9.9mm_P1.27mm | U1, U2, U3 |
| 3 | ULN2803A | SOIC-18W_7.5x11.6mm_P1.27mm | U4, U5, U6 |
| 1 | LM2596S-5.0 | TO-263-5_TabPin3 | U7 |
| 1 | AMS1117-3.3 | SOT-223-3_TabPin2 | U8 |
| 1 | RTL8201F | QFN-32-1EP_5x5mm_P0.5mm_EP3.45x3.45mm_ThermalVias | U9 |
| 1 | 25MHZ 25MHz | Crystal_SMD_5032-2Pin_5.0x3.2mm | Y1 |
| 1 | C8465 Section 1 | TerminalBlock_bornier-2_P5.08mm | J1 |
| 1 | C8465 Section 2 | TerminalBlock_bornier-2_P5.08mm | J2 |
| 1 | C8465 Section 3 | TerminalBlock_bornier-2_P5.08mm | J3 |
| 1 | C8465 Section 4 | TerminalBlock_bornier-2_P5.08mm | J4 |
| 1 | C8465 Section 5 | TerminalBlock_bornier-2_P5.08mm | J5 |
| 1 | C8465 Section 6 | TerminalBlock_bornier-2_P5.08mm | J6 |
| 1 | C8465 Section 7 | TerminalBlock_bornier-2_P5.08mm | J7 |
| 1 | C8465 Section 8 | TerminalBlock_bornier-2_P5.08mm | J8 |
| 1 | C8465 Section 9 | TerminalBlock_bornier-2_P5.08mm | J9 |
| 1 | C8465 Section 10 | TerminalBlock_bornier-2_P5.08mm | J10 |
| 1 | C8465 Section 11 | TerminalBlock_bornier-2_P5.08mm | J11 |
| 1 | C8465 Section 12 | TerminalBlock_bornier-2_P5.08mm | J12 |
| 1 | C8465 Section 13 | TerminalBlock_bornier-2_P5.08mm | J13 |
| 1 | C8465 Section 14 | TerminalBlock_bornier-2_P5.08mm | J14 |
Show 42 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | C8465 Section 15 | TerminalBlock_bornier-2_P5.08mm | J15 |
| 1 | C8465 Section 16 | TerminalBlock_bornier-2_P5.08mm | J16 |
| 1 | C8465 Section 17 | TerminalBlock_bornier-2_P5.08mm | J17 |
| 1 | C8465 Section 18 | TerminalBlock_bornier-2_P5.08mm | J18 |
| 1 | C8465 Section 19 | TerminalBlock_bornier-2_P5.08mm | J19 |
| 1 | C8465 Section 20 | TerminalBlock_bornier-2_P5.08mm | J20 |
| 1 | C8465 Section 21 | TerminalBlock_bornier-2_P5.08mm | J21 |
| 1 | C8465 Section 22 | TerminalBlock_bornier-2_P5.08mm | J22 |
| 1 | C8465 Section 23 | TerminalBlock_bornier-2_P5.08mm | J23 |
| 1 | C8465 Section 24 | TerminalBlock_bornier-2_P5.08mm | J24 |
| 1 | C8465 12V IN | TerminalBlock_bornier-2_P5.08mm | J25 |
| 1 | C8465 12V ACT A (left) | TerminalBlock_bornier-2_P5.08mm | J26 |
| 1 | C8465 12V ACT A (right) | TerminalBlock_bornier-2_P5.08mm | J27 |
| 1 | C8465 12V ACT B (left) | TerminalBlock_bornier-2_P5.08mm | J28 |
| 1 | C8465 12V ACT B (right) | TerminalBlock_bornier-2_P5.08mm | J29 |
| 1 | C319202 DevKitC J2 (3V3..5V) | PinSocket_1x19_P2.54mm_Vertical | J30 |
| 1 | C319202 DevKitC J3 (GND..CLK) | PinSocket_1x19_P2.54mm_Vertical | J31 |
| 1 | HR911105A | RJ45_Hanrun_HR911105A_Horizontal | J32 |
| 1 | I2C | PinHeader_1x04_P2.54mm_Vertical | J33 |
| 1 | C124378 Analog | PinHeader_1x04_P2.54mm_Vertical | J34 |
| 24 | HF115F/012-2ZS4 | Relay_DPDT_Omron_G2RL-2 | K1, K2, K3, K4, K5, K6, K7, K8 +16 |
| 25 | C965805 green | LED_0603_1608Metric | D1, D2, D3, D4, D5, D6, D7, D8 +17 |
| 2 | SS54 | D_SMA | D25, D27 |
| 1 | SMBJ18A | D_SMB | D26 |
| 1 | SS34 | D_SMA | D28 |
| 1 | C2286 red | LED_0603_1608Metric | D29 |
| 1 | C965802 yellow | LED_0603_1608Metric | D30 |
| 1 | C2929502 33uH 3A | L_12x12mm_H8mm | L1 |
| 8 | 100NF 100nF | C_0603_1608Metric | C1, C2, C3, C30, C31, C32, C33, C36 |
| 1 | C97812 100uF 50V | CP_Elec_8x10 | C25 |
| 1 | C165536 220uF 25V | CP_Elec_8x10 | C26 |
| 5 | 10UF 10uF | C_0805_2012Metric | C27, C28, C29, C37, C38 |
| 2 | 33PF 33pF | C_0603_1608Metric | C34, C35 |
| 24 | 2.2K 2.2k | R_0603_1608Metric | R1, R2, R3, R4, R5, R6, R7, R8 +16 |
| 1 | 1k | R_0603_1608Metric | R29 |
| 1 | 33 | R_0603_1608Metric | R30 |
| 1 | C136931 2.49k 1% | R_0603_1608Metric | R31 |
| 6 | 4.7K 4.7k | R_0603_1608Metric | R32, R35, R36, R44, R45, R46 |
| 1 | 10K 10k | R_0603_1608Metric | R33 |
| 1 | 1.5K 1.5k | R_0603_1608Metric | R34 |
| 4 | C23185 49.9 1% | R_0603_1608Metric | R38, R39, R40, R41 |
| 2 | 330 | R_0603_1608Metric | R42, R43 |
Relay24 ESP32 design files
The KiCad project lives in the renatorgr/Boards repository on GitHub; these links point at the commit this page was built from.
Relay24 ESP32: common questions
How big is the Relay24 ESP32 PCB?
The Relay24 ESP32 measures 210 × 120 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Relay24 ESP32?
158 components, from 62 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Relay24 ESP32 design files?
From the renatorgr/Boards repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Relay24 ESP32 design in my own project?
Yes, under the terms of its GPL-3.0 license, which renatorgr chose for the repository.
More boards in Boards
Similar boards
EinkPDA screen
TalismanDesign
95 × 54 mm27 parts2LApache-2.02.0kStack chan
stack-chan
50 × 50 mm33 parts2LApache-2.01.7kDisplay Carrier
AxxAxx
35.6 × 58.2 mm5 parts2LGPL-3.01.7kModule 16S PassiveBalanceAddOn
stuartpittaway
61 × 74 mm86 parts2LCC-BY-NC-4.01.1kTemperaturePCB PANEL
stuartpittaway
116 × 75.5 mm178 parts2LCC-BY-NC-4.01.1kProgrammingAdapter
stuartpittaway
10.5 × 83 mm3 parts2LCC-BY-NC-4.01.1k