K-Line
rickwargo·CATS·K-Line/K-Line.kicad_pcb
About the K-Line PCB
K-Line is an open source ESP32 PCB design by rickwargo, published on GitHub. It is a 2-layer board measuring 75.6 × 64.1 mm, with 61 components from 16 distinct parts.
Its main chip is the ESP32C3-SuperMini, from the ESP32 family. Other key parts include the Mini560 and ER_OLEDM0.91_1x-I2C. By type, the board carries 35 resistors, 11 diodes, 7 capacitors, 4 transistors, 3 ICs and 1 connector.
From the project
An ESP32 system to add some spark into my '00 Z3M
Main components on the K-Line
K-Line bill of materials (BOM)
61 components, 16 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32C3-SuperMini ESP32-C3 SuperMini | ESP32-C3-SuperMini | U1 |
| 1 | Mini560 Mini-560 | Mini-560 | U2 |
| 1 | ER_OLEDM0.91_1x-I2C | ER_OLEDM0.91_1x-I2C | U3 |
| 4 | Q_NMOS_GSD | SC-59_Handsoldering | Q1, Q2, Q3, Q4 |
| 1 | Conn_01x10_Pin | JST_XH_S10B-XH-A-1_1x10_P2.50mm_Horizontal | J1 |
| 2 | Red LED | LED_1206_3216Metric_Pad1.42x1.75mm_HandSolder | D1, D3 |
| 2 | LED | LED_1206_3216Metric_Pad1.42x1.75mm_HandSolder | D2, D4 |
| 7 | 3V3 0.5W | D_SOD-123F | D5, D6, D7, D8, D9, D10, D11 |
| 7 | 100nF | C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C1, C2, C3, C4, C5, C6, C7 |
| 4 | 100R | R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R1, R2, R7, R8 |
| 2 | 220R | R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R3, R9 |
| 2 | 510R | R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R4, R10 |
| 3 | 1K | R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R5, R11, R14 |
| 16 | 10K | R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R6, R12, R15, R16, R18, R19, R21, R22 +8 |
| 1 | 4.7K | R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R13 |
| 7 | 3K3 | R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R17, R20, R23, R26, R29, R32, R35 |
K-Line design files
The KiCad project lives in the rickwargo/CATS repository on GitHub; these links point at the commit this page was built from.
- LayoutK-Line/K-Line.kicad_pcb
- SchematicK-Line/K-Line.kicad_sch
K-Line: common questions
What microcontroller does the K-Line use?
The K-Line is built around the ESP32C3-SuperMini, from the ESP32 family.
How big is the K-Line PCB?
The K-Line measures 75.6 × 64.1 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the K-Line?
61 components, from 16 distinct parts. The full bill of materials is listed on this page.
Where can I download the K-Line design files?
From the rickwargo/CATS repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the K-Line design in my own project?
The repository has no license, so all rights stay with rickwargo. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the K-Line without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in CATS
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k