CATS
rickwargo·CATS
About the CATS PCB
CATS is an open source ESP32 PCB design by rickwargo, published on GitHub. It is a 2-layer board measuring 86 × 70 mm, with 27 components from 22 distinct parts.
Its main chip is the ESP32-S3-DevKitM-1-N8, from the ESP32 family. Other key parts include the MP1584EN, SN65HVD230, Micro_SD_Card, BME-680 and MPU-6050. By type, the board carries 7 connectors, 7 resistors, 6 ICs, 5 capacitors, 1 buzzer and 1 diode.
From the project
An ESP32 system to add some spark into my '00 Z3M
Main components on the CATS
CATS bill of materials (BOM)
27 components, 22 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-DevKitM-1-N8 | ESP32-S3-DevKitM-1-N8 | U1 |
| 1 | MP1584EN ModuleFans | MP1584EN_DCDC_THT_Module | U2 |
| 1 | SN65HVD230 | SOIC-8_3.9x4.9mm_P1.27mm | U4 |
| 1 | Micro_SD_Card | Micro_SD_Card | U5 |
| 1 | BME-680 | BME-680 | U6 |
| 1 | MPU-6050 | MPU-6500 | U8 |
| 1 | Barrel_Jack | BarrelJack_Horizontal | J1 |
| 1 | Conn_01x03 | JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | J2 |
| 1 | Conn_01x07 | JST_XH_B7B-XH-A_1x07_P2.50mm_Vertical | J3 |
| 1 | Conn_01x02 | TerminalBlock_Phoenix_MKDS-1,5-2_1x02_P5.00mm_Horizontal | J4 |
| 1 | Conn_01x04 | JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J5 |
| 2 | Conn_01x05 | JST_XH_B5B-XH-A_1x05_P2.50mm_Vertical | J6, J7 |
| 1 | Buzzer | Passive Buzzer | BZ1 |
| 1 | PESD5V0L2BT | SOT-23 | D8 |
| 1 | 10uF | C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C1 |
| 1 | 100nF | C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C2 |
| 2 | 47pF | C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C4, C5 |
| 1 | 0.1uF | C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C8 |
| 1 | 0R | R_1206_3216Metric | R1 |
| 1 | 4K7 | R_1206_3216Metric | R2 |
Show 2 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | 10R | R_1206_3216Metric | R3, R4 |
| 3 | 10K | R_1206_3216Metric | R8, R9, R10 |
CATS design files
The KiCad project lives in the rickwargo/CATS repository on GitHub; these links point at the commit this page was built from.
- LayoutCATS.kicad_pcb
- SchematicCATS.kicad_sch
CATS: common questions
What microcontroller does the CATS use?
The CATS is built around the ESP32-S3-DevKitM-1-N8, from the ESP32 family.
How big is the CATS PCB?
The CATS measures 86 × 70 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the CATS?
27 components, from 22 distinct parts. The full bill of materials is listed on this page.
Where can I download the CATS design files?
From the rickwargo/CATS repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the CATS design in my own project?
The repository has no license, so all rights stay with rickwargo. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the CATS without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in CATS
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k