PrecisionTimer RevF

SepticElectronics·High-Speed-Timer·PrecisionTimer_RevF/PCB Design Files/PrecisionTimer_RevF.kicad_pcb

PrecisionTimer RevF PCB layout, top view — open source Microchip SAM board by SepticElectronics

About the PrecisionTimer RevF PCB

PrecisionTimer RevF is an open source Microchip SAM PCB design by SepticElectronics, published on GitHub under the GPL-3.0 license. It is a 4-layer board measuring 84.3 × 50.8 mm, with 91 components from 42 distinct parts.

Its main chip is the ATSAM4SD32, from the Microchip SAM family. Other key parts include the TDC7200PW, LCMXO2-256HC-6SG32C, USB2422_MJ, TS30012-M050QFNR and MIC23050-SYML-TR. By type, the board carries 38 capacitors, 14 resistors, 11 inductors, 9 ICs, 9 connectors and 4 crystals.

From the project

High Speed Precision Timer 55ps/4ns

A simple digital timer based on the TDC7200 for high-precision, short burst time measurement with a resolution of up to 55 ps. Long interval, low precision time measurement is done using a 125 MHz oscillator and a DDR-type clocked synchronous counter, implemented in a MachXO2 FPGA with a theoretical resolution of 4 ns. The data collection and interfacing is handled by an ATSAM4S Microcontroller. Two USB 2.0 and a MicroSD Interface are available for data collection.

Main components on the PrecisionTimer RevF

TDC7200PWLCMXO2-256HC-6SG32CUSB2422_MJATSAM4SD32TS30012-M050QFNRMIC23050-SYML-TRAP21410LM74610QDGKTQ1

PrecisionTimer RevF bill of materials (BOM)

91 components, 42 distinct parts.

QtyPartRefs
1
TDC7200PW
U1
1
LCMXO2-256HC-6SG32C
U2
1
USB2422_MJ
U3
1
ATSAM4SD32
U4
1
TS30012-M050QFNR
U5
2
MIC23050-SYML-TR
U6, U9
1
AP21410
U7
1
LM74610QDGKTQ1
U8
1
Q_NMOS_GSD
Q1
1
Crystal_16MHz
X1
1
ASE-125MHz
X2
1
Crystal_24MHz
X3
1
ASE-016MHz
X4
1
USB_B
J1
1
Micro_SD_Card
J2
1
1-1734775-1
J3
1
Barrel_Jack_Switch
J4
3
Conn_Coaxial
J5, J7, J8
1
Conn_02x05_Odd_Even
J6
1
Conn_01x04_Male
J9
Show 22 more
QtyPartRefs
2
Polyfuse_Small
F1, F2
1
LED
D1
1
D_TVS
D2
1
D_Zener_Small
D3
7
Ferrite_Bead_Small
FB1, FB2, FB3, FB4, FB5, FB6, FB7
2
1µH
L1, L3
2
4.7µH
L2, L4
4
10p
C1, C2, C4, C5
17
100n
C3, C8, C10, C16, C18, C19, C20, C21 +9
1
1µ
C6
8
4µ7
C7, C9, C12, C17, C29, C31, C33, C34
2
560p
C11, C28
4
22µ
C13, C14, C15, C32
1
100µ
C30
1
100p
C38
1
12k
R1
5
100k
R2, R3, R4, R5, R6
1
220
R7
4
10k
R8, R9, R10, R11
1
100
R12
1
22R
R13
1
68R
R14

PrecisionTimer RevF design files

The KiCad project lives in the SepticElectronics/High-Speed-Timer repository on GitHub; these links point at the commit this page was built from.

PrecisionTimer RevF: common questions

What microcontroller does the PrecisionTimer RevF use?

The PrecisionTimer RevF is built around the ATSAM4SD32, from the Microchip SAM family.

How big is the PrecisionTimer RevF PCB?

The PrecisionTimer RevF measures 84.3 × 50.8 mm, has 4 copper layers and is 1.6 mm thick.

How many components are on the PrecisionTimer RevF?

91 components, from 42 distinct parts. The full bill of materials is listed on this page.

Where can I download the PrecisionTimer RevF design files?

From the SepticElectronics/High-Speed-Timer repository on GitHub, which has the KiCad layout; the links under Design files point to each one.

Can I use the PrecisionTimer RevF design in my own project?

Yes, under the terms of its GPL-3.0 license, which SepticElectronics chose for the repository.

Can I test firmware for the PrecisionTimer RevF without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug Microchip SAM firmware against it before you order a PCB.

More boards in High-Speed-Timer

Similar boards