PrecisionTimer RevF back
SepticElectronics·High-Speed-Timer·PrecisionTimer_RevF/PCB Design Files/PrecisionTimer_RevF_back.kicad_pcb
About the PrecisionTimer RevF back PCB
PrecisionTimer RevF back is an open source Microchip SAM PCB design by SepticElectronics, published on GitHub under the GPL-3.0 license. It is a 4-layer board measuring 84.3 × 50.8 mm, with 88 components from 38 distinct parts.
Its main chip is the ATSAM4SD32, from the Microchip SAM family. Other key parts include the TDC7200PW, LCMXO2-256HC-6SG32C, USB2422_MJ, TS30012-M050QFNR and MIC23050-SYML-TR. By type, the board carries 37 capacitors, 12 resistors, 11 inductors, 9 ICs, 9 connectors and 4 crystals.
From the project
High Speed Precision Timer 55ps/4ns
A simple digital timer based on the TDC7200 for high-precision, short burst time measurement with a resolution of up to 55 ps. Long interval, low precision time measurement is done using a 125 MHz oscillator and a DDR-type clocked synchronous counter, implemented in a MachXO2 FPGA with a theoretical resolution of 4 ns. The data collection and interfacing is handled by an ATSAM4S Microcontroller. Two USB 2.0 and a MicroSD Interface are available for data collection.
Main components on the PrecisionTimer RevF back
PrecisionTimer RevF back bill of materials (BOM)
88 components, 38 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | TDC7200PW | SOP65P640X120-14N | U1 |
| 1 | LCMXO2-256HC-6SG32C | QFN50P500X500X60-33N | U2 |
| 1 | USB2422_MJ | QFN50P400X400X100-25N-D | U3 |
| 1 | ATSAM4SD32 | TFBGA-100_9.0x9.0mm_Layout10x10_P0.8mm | U4 |
| 1 | TS30012-M050QFNR | QFN50P300X300X100-17N-D | U5 |
| 2 | MIC23050-SYML-TR | SON50P200X200X90-9N | U6, U8 |
| 1 | AP21410 | DFN-6-1EP_2x1.8mm_P0.5mm_EP1.2x1.6mm | U7 |
| 1 | LM74610QDGKTQ1 | SOP65P490X110-8N | U9 |
| 1 | Q_NMOS_GSD | SOT-23 | Q1 |
| 2 | Crystal_GND24 | Crystal_SMD_2016-4Pin_2.0x1.6mm | X1, X3 |
| 1 | ASE-xxxMHz | Oscillator_SMD_SeikoEpson_SG210-4Pin_2.5x2.0mm | X2 |
| 1 | ASE-xxxMHz | Oscillator_SMD_EuroQuartz_XO32-4Pin_3.2x2.5mm | X4 |
| 1 | USB_B | KUSBEXSMTBS1NBTR | J1 |
| 1 | Micro_SD_Card | 475710001 | J2 |
| 1 | 1-1734775-1 | 117347751 | J3 |
| 1 | Barrel_Jack_Switch | BarrelJack_Wuerth_6941xx301002 | J4 |
| 3 | Conn_Coaxial | SMA_Molex_73251-2200_Horizontal | J5, J7, J8 |
| 1 | Conn_02x05_Odd_Even | PinHeader_2x05_P2.54mm_Vertical_SMD | J6 |
| 1 | Conn_01x04_Male | PinHeader_1x04_P2.54mm_Vertical_SMD_Pin1Left | J9 |
| 2 | Polyfuse_Small | Fuse_1206_3216Metric_Castellated | F1, F2 |
Show 18 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | LED | LED_D3.0mm | D1 |
| 1 | D_Zener_Small | D_MiniMELF | D2 |
| 1 | D_TVS | D_SMB | D3 |
| 7 | Ferrite_Bead_Small | L_0603_1608Metric | FB1, FB2, FB3, FB4, FB5, FB6, FB7 |
| 2 | 1µH | L_0805_2012Metric | L1, L3 |
| 2 | 4.7µH | L_0805_2012Metric | L2, L4 |
| 4 | 10p | C_0402_1005Metric | C1, C2, C4, C5 |
| 17 | 100n | C_0603_1608Metric | C3, C8, C14, C15, C16, C17, C19, C20 +9 |
| 1 | 1µ | C_0603_1608Metric | C6 |
| 8 | 4µ7 | C_0603_1608Metric | C7, C10, C18, C33, C35, C36, C37, C39 |
| 2 | 560p | C_0603_1608Metric | C9, C34 |
| 4 | 22µ | C_0805_2012Metric | C11, C12, C13, C38 |
| 1 | 100µ | CP_Elec_5x5.4 | C32 |
| 1 | 12k | R_0402_1005Metric | R1 |
| 5 | 100k | R_0402_1005Metric | R2, R3, R4, R5, R6 |
| 1 | 220 | R_0603_1608Metric | R7 |
| 1 | 100 | R_0805_2012Metric | R8 |
| 4 | 10k | R_0603_1608Metric | R9, R10, R11, R12 |
PrecisionTimer RevF back design files
The KiCad project lives in the SepticElectronics/High-Speed-Timer repository on GitHub; these links point at the commit this page was built from.
PrecisionTimer RevF back: common questions
What microcontroller does the PrecisionTimer RevF back use?
The PrecisionTimer RevF back is built around the ATSAM4SD32, from the Microchip SAM family.
How big is the PrecisionTimer RevF back PCB?
The PrecisionTimer RevF back measures 84.3 × 50.8 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the PrecisionTimer RevF back?
88 components, from 38 distinct parts. The full bill of materials is listed on this page.
Where can I download the PrecisionTimer RevF back design files?
From the SepticElectronics/High-Speed-Timer repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the PrecisionTimer RevF back design in my own project?
Yes, under the terms of its GPL-3.0 license, which SepticElectronics chose for the repository.
Can I test firmware for the PrecisionTimer RevF back without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug Microchip SAM firmware against it before you order a PCB.
More boards in High-Speed-Timer
Microchip SAM
PrecisionTimer RevG-1
SepticElectronics
84.3 × 50.8 mm99 parts4LGPL-3.00Microchip SAM
PrecisionTimer RevG
SepticElectronics
84.3 × 50.8 mm98 parts4LGPL-3.00Microchip SAM
PrecisionTimer RevF
SepticElectronics
84.3 × 50.8 mm91 parts4LGPL-3.00Microchip SAM
PrecisionTimer RevF back2
SepticElectronics
84.3 × 50.8 mm88 parts4LGPL-3.00
Similar boards
Microchip SAM
Microcontroller Expansion Card
FrameworkComputer
26 × 30 mm24 parts2LCC-BY-4.01.1kMicrochip SAM
Taco Raven
VoronDesign
120 × 113 mm349 parts4LGPL-3.01.1kMicrochip SAM
Fpgaboy
Wren6991
50 × 50 mm89 parts4LNo license511Microchip SAM
OpenDropV4
GaudiLabs
124 × 115.4 mm118 parts2LGPL-3.0487Microchip SAM
ModulAdapter universal
GaudiLabs
100 × 69.5 mm45 parts2LGPL-3.0487Microchip SAM
Kira
kiibohd
366.9 × 114.3 mm400 partsCERN-OHL-1.2416