PrecisionTimer RevG-1

SepticElectronics·High-Speed-Timer·PrecisionTimer_RevG.1/PCB Design Files/PrecisionTimer_RevG-1.kicad_pcb

PrecisionTimer RevG-1 PCB layout, top view — open source Microchip SAM board by SepticElectronics

About the PrecisionTimer RevG-1 PCB

PrecisionTimer RevG-1 is an open source Microchip SAM PCB design by SepticElectronics, published on GitHub under the GPL-3.0 license. It is a 4-layer board measuring 84.3 × 50.8 mm, with 99 components from 44 distinct parts.

Its main chip is the ATSAM4S2, from the Microchip SAM family. Other key parts include the TDC7200PW, LCMXO2-256HC-6SG32C, VNC2-32Q1C-REEL, TS30012-M050QFNR and MIC23050-SYML-TR. By type, the board carries 43 capacitors, 15 resistors, 10 ICs, 10 inductors, 9 connectors and 5 crystals.

From the project

High Speed Precision Timer 55ps/4ns

A simple digital timer based on the TDC7200 for high-precision, short burst time measurement with a resolution of up to 55 ps. Long interval, low precision time measurement is done using a 125 MHz oscillator and a DDR-type clocked synchronous counter, implemented in a MachXO2 FPGA with a theoretical resolution of 4 ns. The data collection and interfacing is handled by an ATSAM4S Microcontroller. Two USB 2.0 and a MicroSD Interface are available for data collection.

Main components on the PrecisionTimer RevG-1

TDC7200PWLCMXO2-256HC-6SG32CVNC2-32Q1C-REELATSAM4S2TS30012-M050QFNRMIC23050-SYML-TRMIC23050-4YML-TRLM74610QDGKTQ1MIC2095-2YMT-TR

PrecisionTimer RevG-1 bill of materials (BOM)

99 components, 44 distinct parts.

QtyPartRefs
1
TDC7200PW
U1
1
LCMXO2-256HC-6SG32C
U2
1
VNC2-32Q1C-REEL
U3
1
ATSAM4S2
U4
1
TS30012-M050QFNR
U5
1
MIC23050-SYML-TR
U6
1
MIC23050-4YML-TR
U7
1
LM74610QDGKTQ1
U8
2
MIC2095-2YMT-TR
U9, U10
1
NMOS 2A
Q1
2
ECS-160-8-36B-CKY-TR
X1, X5
1
DSC1001DI2-125.0000
X2
1
FC-135 32.7680KA-AG0
X3
1
ECS-3225S33-160-FN-TR
X4
1
USB_B
J1
1
USB_A
J2
1
Barrel_Jack_Switch
J3
1
Micro_SD_Card
J4
1
Conn_02x05_Odd_Even
J5
1
Conn_01x04_Male
J6
Show 24 more
QtyPartRefs
3
Conn_Coaxial
J7, J8, J9
2
Polyfuse 500 mA
F1, F2
1
LED
D1
1
TVS 28V
D2
1
Zener 5.6V
D3
1
D1213A-02SO-7
D4
6
Ferrite 2A 330R
FB1, FB2, FB3, FB4, FB5, FB6
2
1µH
L1, L2
2
4.7µH
L3, L4
6
10p
C1, C2, C4, C5, C40, C41
19
100n
C3, C8, C10, C14, C18, C19, C20, C21 +11
10
4µ7
C6, C7, C9, C12, C17, C29, C31, C33 +2
2
560p
C11, C28
1
10µ
C13
3
22µ
C15, C16, C32
1
100µ
C30
1
100p
C38
3
47k
R1, R2, R3
1
1k
R4
5
10k
R5, R6, R7, R8, R14
3
0R
R9, R10, R13
1
22R
R11
1
68R
R12
1
100k
R15

PrecisionTimer RevG-1 design files

The KiCad project lives in the SepticElectronics/High-Speed-Timer repository on GitHub; these links point at the commit this page was built from.

PrecisionTimer RevG-1: common questions

What microcontroller does the PrecisionTimer RevG-1 use?

The PrecisionTimer RevG-1 is built around the ATSAM4S2, from the Microchip SAM family.

How big is the PrecisionTimer RevG-1 PCB?

The PrecisionTimer RevG-1 measures 84.3 × 50.8 mm, has 4 copper layers and is 1.6 mm thick.

How many components are on the PrecisionTimer RevG-1?

99 components, from 44 distinct parts. The full bill of materials is listed on this page.

Where can I download the PrecisionTimer RevG-1 design files?

From the SepticElectronics/High-Speed-Timer repository on GitHub, which has the KiCad layout; the links under Design files point to each one.

Can I use the PrecisionTimer RevG-1 design in my own project?

Yes, under the terms of its GPL-3.0 license, which SepticElectronics chose for the repository.

Can I test firmware for the PrecisionTimer RevG-1 without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug Microchip SAM firmware against it before you order a PCB.

More boards in High-Speed-Timer

Similar boards