FlightController
Simonhajd·Triton-Float·PCB/FlightController/FlightController.kicad_pcb
About the FlightController PCB
FlightController is an open source ESP32 PCB design by Simonhajd, published on GitHub. It is a 2-layer board measuring 100 × 100 mm, with 19 components from 15 distinct parts.
Its main chip is the XIAO-ESP32-S3-PLUS-SMD, from the ESP32 family. Other key parts include the RFM95W and MS583702BA01-50. By type, the board carries 8 resistors, 6 connectors, 2 ICs and 1 module.
It belongs with the rf & radio and sensors designs in this gallery.
From the project
Float Repo for the 2026 Triton Float
Development repository for the 2026 Triton Robotics Float.
The Triton Float is being developed for the 2026 MATE ROV Pioneer competition (Newfoundland). This design iteration is approximately 33% smaller than last year's model, while targeting more than 2× performance improvements in speed and significantly increased precision through layered redundancy and sensor feedback systems. It also includes a dedicated LoRa radio as opposed to last year's 4cm wire antenna, which will increase the reliability and robustness of the system.
Main components on the FlightController
FlightController bill of materials (BOM)
19 components, 15 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | XIAO-ESP32-S3-PLUS-SMD XIAO-nRF52840-DIP | XIAO-nRF52840-DIP | U1 |
| 1 | RFM95W | HOPERF_RFM9XW_THT | U2 |
| 1 | MS583702BA01-50 | XDCR_MS583702BA01-50 | A1 |
| 1 | SMA Connector | CONN_RF2-04A-T-00-50-G_ADM | J1 |
| 1 | CONN_01X02 BATT IN | PinHeader_1x01_P2.54mm_Vertical | J2 |
| 1 | BATT OUT | PinHeader_1x01_P2.54mm_Vertical | J3 |
| 1 | 530470510 BATT Reg IC | PinHeader_1x03_P2.54mm_Vertical | J4 |
| 1 | Pressure sensor | JST_GH_BM04B-GHS-TBT_1x04-1MP_P1.25mm_Vertical | J6 |
| 1 | 530470510 | MOLEX_530470510 | J8 |
| 2 | DMP3068L-7 | SOT-23_DMP3068L_DIO | MOSFET1, MOSFET2 |
| 3 | 4.7k | R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R1, R2, R7 |
| 1 | 220 0.1uF | R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R3 |
| 1 | 10uF | R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R4 |
| 2 | 4.7K 4.7k | R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R5, R6 |
| 1 | 10k | R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R8 |
FlightController design files
The KiCad project lives in the Simonhajd/Triton-Float repository on GitHub; these links point at the commit this page was built from.
FlightController: common questions
What microcontroller does the FlightController use?
The FlightController is built around the XIAO-ESP32-S3-PLUS-SMD, from the ESP32 family.
How big is the FlightController PCB?
The FlightController measures 100 × 100 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the FlightController?
19 components, from 15 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the FlightController design files?
From the Simonhajd/Triton-Float repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the FlightController design in my own project?
The repository has no license, so all rights stay with Simonhajd. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the FlightController without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in Triton-Float
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k