FlightController-Chipstyle

Simonhajd·Triton-Float·Controlexp/FlightController-Chipstyle.kicad_pcb

FlightController-Chipstyle PCB layout, top view — open source ESP32 board by Simonhajd

About the FlightController-Chipstyle PCB

FlightController-Chipstyle is an open source ESP32 PCB design by Simonhajd, published on GitHub. It is a 2-layer board measuring 100 × 100 mm, with 15 components from 13 distinct parts.

Its main chip is the XIAO-ESP32-S3-PLUS-SMD, from the ESP32 family. Other key parts include the RFM95W and MS583702BA01-50. By type, the board carries 6 resistors, 5 connectors, 2 ICs, 1 module and 1 transistor.

It belongs with the rf & radio and sensors designs in this gallery.

From the project

Float Repo for the 2026 Triton Float

Development repository for the 2026 Triton Robotics Float.

The Triton Float is being developed for the 2026 MATE ROV Pioneer competition (Newfoundland). This design iteration is approximately 33% smaller than last year's model, while targeting more than 2× performance improvements in speed and significantly increased precision through layered redundancy and sensor feedback systems. It also includes a dedicated LoRa radio as opposed to last year's 4cm wire antenna, which will increase the reliability and robustness of the system.

FlightController-Chipstyle, from the project README
From the project README

Main components on the FlightController-Chipstyle

FlightController-Chipstyle bill of materials (BOM)

15 components, 13 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
XIAO-ESP32-S3-PLUS-SMD
XIAO-nRF52840-DIP
U1
1
RFM95W
U2
1
MS583702BA01-50
A1
1
P_CHANNEL
Q1
1
SMA Connector
J1
1
530470510
BATT Reg IC
J4
1
Pressure sensor
J6
1
HallCircuit
J7
1
530470510
J8
1
0.1uF
R1
2
10uF
R2, R4
1
220
0.1uF
R3
2
4.7K
4.7k
R5, R6

FlightController-Chipstyle design files

The KiCad project lives in the Simonhajd/Triton-Float repository on GitHub; these links point at the commit this page was built from.

FlightController-Chipstyle: common questions

What microcontroller does the FlightController-Chipstyle use?

The FlightController-Chipstyle is built around the XIAO-ESP32-S3-PLUS-SMD, from the ESP32 family.

How big is the FlightController-Chipstyle PCB?

The FlightController-Chipstyle measures 100 × 100 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the FlightController-Chipstyle?

15 components, from 13 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the FlightController-Chipstyle design files?

From the Simonhajd/Triton-Float repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.

Can I use the FlightController-Chipstyle design in my own project?

The repository has no license, so all rights stay with Simonhajd. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the FlightController-Chipstyle without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

More boards in Triton-Float

Similar boards