Controlexp

Simonhajd·Triton-Float·Controlexp/Controlexp.kicad_pcb

Controlexp PCB layout, top view — open source ESP32 board by Simonhajd

About the Controlexp PCB

Controlexp is an open source ESP32 PCB design by Simonhajd, published on GitHub. It is a 2-layer board measuring 98.7 × 59.6 mm, with 36 components from 29 distinct parts.

Its main chip is the XIAO-ESP32-S3-PLUS-SMD, from the ESP32 family. Other key parts include the RFM95W, TPS62162DSG, TPS62163DSG, SN74LVC1T45DBV and BMP388. By type, the board carries 12 capacitors, 10 connectors, 6 ICs, 3 resistors, 2 diodes and 2 inductors.

It belongs with the rf & radio and sensors designs in this gallery.

From the project

Float Repo for the 2026 Triton Float

Development repository for the 2026 Triton Robotics Float.

The Triton Float is being developed for the 2026 MATE ROV Pioneer competition (Newfoundland). This design iteration is approximately 33% smaller than last year's model, while targeting more than 2× performance improvements in speed and significantly increased precision through layered redundancy and sensor feedback systems. It also includes a dedicated LoRa radio as opposed to last year's 4cm wire antenna, which will increase the reliability and robustness of the system.

Controlexp, from the project README
From the project README

Main components on the Controlexp

Controlexp bill of materials (BOM)

36 components, 29 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
XIAO-ESP32-S3-PLUS-SMD
XIAO-ESP32-S3-Plus-SMD
U1
1
RFM95W
U2
1
TPS62162DSG
U3
1
TPS62163DSG
U5
1
SN74LVC1T45DBV
U6
1
BMP388
U7
1
Conn_Coaxial_Small
J1
1
CONN_01X02
Conn_01x02
J2
1
530470510
J4
1
Power Connector
J5
1
Pressure sensor
J6
1
ToF sensor
J7
1
LED
J8
1
PWRCONN
J9
1
Extra sensor TOP
J10
1
Extra sensor BOTTOM
J11
1
CONN_01X02
Conn_01x02
JBUTT1
1
RED
D1
1
SS34
D2
2
2.2UH
2.2uH
L1, L2
Show 9 more
QtyPartRefs
2
0.1UF
0.1uF
C1, C3
2
10UF
10uF
C2, C4
2
10uF, 25V
C5, C11
1
22uF, 6.3V
C6
2
220 uF
C9, C10
1
22uF, 10V
C12
2
100NF
100nF
C13, C14
1
220
R3
2
4.7K
4.7k
R5, R6

Controlexp design files

The KiCad project lives in the Simonhajd/Triton-Float repository on GitHub; these links point at the commit this page was built from.

Controlexp: common questions

What microcontroller does the Controlexp use?

The Controlexp is built around the XIAO-ESP32-S3-PLUS-SMD, from the ESP32 family.

How big is the Controlexp PCB?

The Controlexp measures 98.7 × 59.6 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Controlexp?

36 components, from 29 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Controlexp design files?

From the Simonhajd/Triton-Float repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Controlexp design in my own project?

The repository has no license, so all rights stay with Simonhajd. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Controlexp without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

More boards in Triton-Float

Similar boards