Mohawk
sparques·mohawk·mohawk/mohawk.kicad_pcb
About the Mohawk PCB
Mohawk is an open source PCB design by sparques, published on GitHub under the GPL-2.0 license. It is a 2-layer board measuring 65 × 30 mm, with 50 components from 27 distinct parts.
Other key parts include the CAT24C256, SC16IS752IPW_128, MAX232 and TLV320AIC3204IRHBR. By type, the board carries 19 resistors, 18 capacitors, 5 ICs, 4 connectors, 1 crystal and 1 speaker.
It belongs with the rf & radio and audio designs in this gallery.
From the project
DRA818-based radio µHat for the raspberry pi family of SBCs.
Mohawk is the second iteration of RADIC-818: a Raspberry Pi Zero µHAT-sized UHF/VHF radio interface built around a DRA818V radio module. It brings the radio's audio, configuration UART, and push-to-talk control to a Raspberry Pi, and provides an RS-232 port for an external device. The current design is a KiCad 10 schematic and two-layer PCB. Hardware validation has not been recorded in this repository.

Main components on the Mohawk
Mohawk bill of materials (BOM)
50 components, 27 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | CAT24C256 | SOIC8_ONS | U1 |
| 1 | SC16IS752IPW_128 | TSSOP28_SOT361-1_NXP | U2 |
| 1 | ~ | DRA818 | U3 |
| 1 | MAX232 | PW16 | U4 |
| 1 | TLV320AIC3204IRHBR | RHB0032E_NV | U5 |
| 1 | ASE-1.8432MHz | Oscillator_SMD_Abracon_ASE-4Pin_3.2x2.5mm | Y1 |
| 1 | GPIO | PinSocket_2x20_P2.54mm_Vertical | J1 |
| 1 | SMA | SMA_BAT_Wireless_BWSMA-KWE-Z001 | J2 |
| 1 | UI Header | 1x05 SMD pads | J3 |
| 1 | DB9 Header | 1x05 SMD pads | J4 |
| 1 | Speaker | PinHeader_1x02_P2.54mm_Vertical | LS1 |
| 1 | ID_WP | SolderJumper-2_P1.3mm_Open_Pad1.0x1.5mm | WP1 |
| 1 | ~ | D_0805_2012Metric | D1 |
| 5 | 100nF | C_0805_2012Metric | C1, C10, C13, C14, C16 |
| 2 | 4.7µF | C_0805_2012Metric | C2, C3 |
| 5 | 1µF | C_0805_2012Metric | C4, C5, C6, C7, C8 |
| 4 | 10uF | C_0805_2012Metric | C9, C11, C12, C15 |
| 1 | 10µF | C_0805_2012Metric | C17 |
| 1 | 47µF | C_0805_2012Metric | C18 |
| 3 | 4.7k | R_0805_2012Metric | R1, R11, R12 |
Show 7 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 3 | 10k | R_0805_2012Metric | R2, R8, R13 |
| 2 | 3.9k | R_0805_2012Metric | R3, R4 |
| 3 | R_Small | R_0805_2012Metric | R5, R10, R14 |
| 2 | 0 | R_0805_2012Metric | R6, R9 |
| 1 | 1k | R_0805_2012Metric | R7 |
| 1 | 10 | R_0805_2012Metric | R15 |
| 4 | 27 | R_0805_2012Metric | R16, R17, R18, R19 |
Mohawk design files
The KiCad project lives in the sparques/mohawk repository on GitHub; these links point at the commit this page was built from.
- Layoutmohawk/mohawk.kicad_pcb
- Schematicmohawk/mohawk.kicad_sch
- BOMREADME.md
Mohawk: common questions
How big is the Mohawk PCB?
The Mohawk measures 65 × 30 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Mohawk?
50 components, from 27 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Mohawk design files?
From the sparques/mohawk repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Mohawk design in my own project?
Yes, under the terms of its GPL-2.0 license, which sparques chose for the repository.
Similar boards
KLOR
GEIGEIGEIST
160.2 × 118.3 mm79 parts2LGPL-3.01.2kButtonsLEDs
shanteacontrols
390 × 37 mm82 parts2LApache-2.0956USB
shanteacontrols
52 × 12.6 mm6 parts2LApache-2.0956Pots
shanteacontrols
390 × 93 mm75 parts2LApache-2.0956PicoGUS Hand386
polpo
29.2 × 75.2 mm43 parts4LGPL-2.0800Snark barker
schlae
231.1 × 106.7 mm193 parts2LNo license687