Loop test
speck0413·ai-native-eda·examples/loop-test/kicad/loop-test.kicad_pcb
About the Loop test PCB
Loop test is an open source ESP32 PCB design by speck0413, published on GitHub under the MIT license. It is a 2-layer board measuring 18 × 16 mm, with 11 components from 9 distinct parts.
Its main chip is the ESP32-C3-WROOM-02, from the ESP32 family. By type, the board carries 4 resistors, 3 capacitors, 2 diodes, 1 IC and 1 connector.
From the project
Intent-level PCB layout for AI agents
The current board.ts is the repaired result of the 2026-10-07 experiment, not the initial broken challenge described by its historical opening comment. The original challenge kept an 18 × 16 mm outline, added an LED pair and tightened VIN decoupling; the experiment logs record the edits and requirement relaxation. Do not mistake that run for validation under current release rules.
Main components on the Loop test
Loop test bill of materials (BOM)
11 components, 9 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-C3-WROOM-02 AP2112K-3.3 | SOT-23-5 | U1 |
| 1 | USB4105-GF-A | USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J1 |
| 1 | B5819W green | LED_0603_1608Metric | D1 |
| 1 | red | LED_0603_1608Metric | D2 |
| 2 | 10u | C_0603_1608Metric | C1, C2 |
| 1 | 100n | C_0402_1005Metric | C3 |
| 2 | 5.1k | R_0402_1005Metric | R1, R2 |
| 1 | 330 | R_0402_1005Metric | R3 |
| 1 | 1k | R_0402_1005Metric | R4 |
Loop test design files
The KiCad project lives in the speck0413/ai-native-eda repository on GitHub; these links point at the commit this page was built from.
Loop test: common questions
What microcontroller does the Loop test use?
The Loop test is built around the ESP32-C3-WROOM-02, from the ESP32 family.
How big is the Loop test PCB?
The Loop test measures 18 × 16 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Loop test?
11 components, from 9 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Loop test design files?
From the speck0413/ai-native-eda repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Loop test design in my own project?
Yes, under the terms of its MIT license, which speck0413 chose for the repository.
Can I test firmware for the Loop test without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in ai-native-eda
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k