Esp32c3-devkit
speck0413·ai-native-eda·examples/esp32c3-devkit/kicad/esp32c3-devkit.kicad_pcb
About the Esp32c3-devkit PCB
Esp32c3-devkit is an open source ESP32 PCB design by speck0413, published on GitHub under the MIT license. It is a 4-layer board measuring 27.9 × 48.3 mm, with 43 components from 21 distinct parts.
Its main chip is the ESP32-C3-WROOM-02, from the ESP32 family. Other key parts include the AP2112K-3.3, SX1509B and USBLC6-2SC6. By type, the board carries 16 resistors, 14 capacitors, 4 ICs, 4 connectors, 3 diodes and 2 switches.
It belongs with the usb & debug tools designs in this gallery.
From the project
Intent-level PCB layout for AI agents
A breakout for the ESP32-C3-WROOM-02 module in the ESP32-DevKitC V4 mechanical and 38-pin header-label layout. It preserves the recorded power/header map, but native C3 and I2C-expander GPIO differ from the original ESP32: ADC, peripheral functions, boot behavior and firmware are not interchangeable. Check a carrier's electrical expectations against the pin map below. Built by aieda from board.ts; this README is the human-facing record.
Main components on the Esp32c3-devkit
Esp32c3-devkit bill of materials (BOM)
43 components, 21 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-C3-WROOM-02 | ESP32-C3-WROOM-02 | U1 |
| 1 | AP2112K-3.3 | SOT-23-5 | U2 |
| 1 | SX1509B | WQFN-28-1EP_4x4mm_P0.4mm_EP2.7x2.7mm | U3 |
| 1 | USBLC6-2SC6 | SOT-23-6 | U4 |
| 1 | USB4105-GF-A | USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J1 |
| 2 | PinHeader_1x19_P2.54mm_Vertical | PinHeader_1x19_P2.54mm_Vertical | J2, J3 |
| 1 | DM3AT-SF-PEJM5 | microSD_HC_Hirose_DM3AT-SF-PEJM5 | J4 |
| 2 | PTS810 | SW_SPST_PTS810 | SW1, SW2 |
| 1 | B5819W | D_SOD-123 | D1 |
| 1 | red | LED_0603_1608Metric | D2 |
| 1 | green | LED_0603_1608Metric | D3 |
| 1 | 10u | C_0402_1005Metric | C1 |
| 8 | 100n | C_0402_1005Metric | C2, C6, C7, C9, C10, C11, C13, C14 |
| 2 | 1u | C_0402_1005Metric | C3, C12 |
| 3 | 10u | C_0603_1608Metric | C4, C5, C8 |
| 6 | 10k | R_0402_1005Metric | R1, R2, R5, R6, R7, R10 |
| 2 | 5.1k | R_0402_1005Metric | R3, R4 |
| 2 | 47k | R_0402_1005Metric | R8, R9 |
| 2 | 4.7k | R_0402_1005Metric | R11, R12 |
| 2 | 1k | R_0402_1005Metric | R13, R14 |
Show 1 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | 33 | R_0402_1005Metric | R15, R16 |
Esp32c3-devkit design files
The KiCad project lives in the speck0413/ai-native-eda repository on GitHub; these links point at the commit this page was built from.
Esp32c3-devkit: common questions
What microcontroller does the Esp32c3-devkit use?
The Esp32c3-devkit is built around the ESP32-C3-WROOM-02, from the ESP32 family.
How big is the Esp32c3-devkit PCB?
The Esp32c3-devkit measures 27.9 × 48.3 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the Esp32c3-devkit?
43 components, from 21 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Esp32c3-devkit design files?
From the speck0413/ai-native-eda repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Esp32c3-devkit design in my own project?
Yes, under the terms of its MIT license, which speck0413 chose for the repository.
Can I test firmware for the Esp32c3-devkit without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in ai-native-eda
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k