Mech test
speck0413·ai-native-eda·examples/mech-test/kicad/mech-test.kicad_pcb
About the Mech test PCB
Mech test is an open source ESP32 PCB design by speck0413, published on GitHub under the MIT license. It is a 2-layer board measuring 22 × 16 mm, with 9 components from 7 distinct parts.
Its main chip is the ESP32-C3-WROOM-02, from the ESP32 family. By type, the board carries 3 capacitors, 3 resistors, 1 IC, 1 connector and 1 diode.
From the project
Intent-level PCB layout for AI agents
The smoke board plus the mechanical items the DSL gained on 2026-10-08: a plated M2 mounting hole on GND (b.hole), three fiducials (b.fiducials), a VBUS test point (b.tp). The retained result predates current trace-specification and release-evidence rules. Built to prove the mechanism, not to order: the 22x16 mm board is crowded by the keepouts, so one region constraint misses by 0.33 mm and one VBUS run necks below its class width; both are reported by the build. 0 DRC errors, 0 unconnected; the BOM and CPL carry no mechanical parts.
Main components on the Mech test
Mech test bill of materials (BOM)
9 components, 7 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-C3-WROOM-02 AP2112K-3.3 | SOT-23-5 | U1 |
| 1 | USB4105-GF-A | USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J1 |
| 1 | B5819W green | LED_0603_1608Metric | D1 |
| 2 | 10u | C_0603_1608Metric | C1, C2 |
| 1 | 100n | C_0402_1005Metric | C3 |
| 1 | 330 | R_0402_1005Metric | R1 |
| 2 | 5.1k | R_0402_1005Metric | R2, R3 |
Mech test design files
The KiCad project lives in the speck0413/ai-native-eda repository on GitHub; these links point at the commit this page was built from.
Mech test: common questions
What microcontroller does the Mech test use?
The Mech test is built around the ESP32-C3-WROOM-02, from the ESP32 family.
How big is the Mech test PCB?
The Mech test measures 22 × 16 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Mech test?
9 components, from 7 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Mech test design files?
From the speck0413/ai-native-eda repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Mech test design in my own project?
Yes, under the terms of its MIT license, which speck0413 chose for the repository.
Can I test firmware for the Mech test without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in ai-native-eda
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k