SensebenderMicro2
tbowmo·SensebenderMicro2
About the SensebenderMicro2 PCB
SensebenderMicro2 is an open source Microchip SAM PCB design by tbowmo, published on GitHub. It is a 2-layer board measuring 21.5 × 32 mm, with 40 components from 27 distinct parts.
Its main chip is the ATSAMD20E, from the Microchip SAM family. Other key parts include the MCP1703T-3302E, NRF24L01, RFM69HW, ATSHA204A and AT45DB041E. By type, the board carries 14 capacitors, 8 ICs, 5 resistors, 2 connectors, 2 jumpers and 2 diodes.
It belongs with the sensors designs in this gallery.
From the project
Sensebender Micro V2
Revamped Sensebender Micro, with Atmel SAMD20 processor instead of atmega 328p.
- up to 256Kb flash/32Kb RAM for code - up to 48Mhz operating freq. - 2 LEDs - Dual radio - RFM69 - NRF24 mini / smd - onboard voltage regulator, can be disabled / bypassed with solderbridges - Temperature / Humidity sensor Si7021 - Onboard external flash for future OTA (bootloader is not developed yet) - Use MYSX2.4 connector for add-on boards
Main components on the SensebenderMicro2
SensebenderMicro2 bill of materials (BOM)
40 components, 27 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ATSAMD20E | TQFP-32_7x7mm_Pitch0.8mm | U1 |
| 1 | MCP1703T-3302E | SOT-23 | U2 |
| 1 | NRF24L01 | NRF24L01-SMD | U3 |
| 1 | RFM69HW | RFM95HW_SMD | U4 |
| 1 | ATSHA204A | SOT-23 | U5 |
| 1 | AT45DB041E | SOIC-8_3.9x4.9mm_Pitch1.27mm | U6 |
| 1 | Si7021 | DFN-6-1EP_3x3mm_Pitch0.95mm | U7 |
| 1 | 24AA32AT-I/OT | SOT-23-5 | U8 |
| 1 | 32Khz | XTAL_3.2x1.5mm | Y1 |
| 1 | MYSX_2.4 | MYSX_2.4 | P2 |
| 1 | Antenna | Pin_Header_Straight_1x02 | P3 |
| 1 | PWR SELECT | 3_pin_solder_jumper_smd | JP1 |
| 1 | JUMPER | 2_pin_solder_jumper_smd | JP2 |
| 1 | GND | Measurement_Point_Round-SMD-Pad_Small | W1 |
| 1 | RESET | Measurement_Point_Round-SMD-Pad_Small | W2 |
| 1 | SWCLK | Measurement_Point_Round-SMD-Pad_Small | W3 |
| 1 | SWDIO | Measurement_Point_Round-SMD-Pad_Small | W4 |
| 1 | VCC | Measurement_Point_Round-SMD-Pad_Small | W5 |
| 2 | LED | LED-0603 | D1, D3 |
| 1 | FILTER | R_0603 | FB1 |
Show 7 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 9 | 100nF | C_0603 | C1, C2, C4, C5, C6, C7, C8, C9 +1 |
| 1 | 10nF | C_0603 | C3 |
| 3 | 10uF | C_0603 | C10, C11, C14 |
| 1 | C | C_0603 | C12 |
| 1 | 100K | R_0603 | R1 |
| 2 | 220R | R_0603 | R2, R6 |
| 2 | 4k7 | R_0603 | R4, R5 |
SensebenderMicro2 design files
The KiCad project lives in the tbowmo/SensebenderMicro2 repository on GitHub; these links point at the commit this page was built from.
SensebenderMicro2: common questions
What microcontroller does the SensebenderMicro2 use?
The SensebenderMicro2 is built around the ATSAMD20E, from the Microchip SAM family.
How big is the SensebenderMicro2 PCB?
The SensebenderMicro2 measures 21.5 × 32 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the SensebenderMicro2?
40 components, from 27 distinct parts. The full bill of materials is listed on this page.
Where can I download the SensebenderMicro2 design files?
From the tbowmo/SensebenderMicro2 repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the SensebenderMicro2 design in my own project?
The repository has no license, so all rights stay with tbowmo. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the SensebenderMicro2 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug Microchip SAM firmware against it before you order a PCB.
Similar boards
Microchip SAM
Microcontroller Expansion Card
FrameworkComputer
26 × 30 mm24 parts2LCC-BY-4.01.1kMicrochip SAM
Taco Raven
VoronDesign
120 × 113 mm349 parts4LGPL-3.01.1kMicrochip SAM
Fpgaboy
Wren6991
50 × 50 mm89 parts4LNo license511Microchip SAM
OpenDropV4
GaudiLabs
124 × 115.4 mm118 parts2LGPL-3.0487Microchip SAM
ModulAdapter universal
GaudiLabs
100 × 69.5 mm45 parts2LGPL-3.0487Microchip SAM
Kira
kiibohd
366.9 × 114.3 mm400 partsCERN-OHL-1.2416