PitBox

Titouan-Beaurepaire·PitBox·pcb/PitBox-PCB.kicad_sch

This repository ships a schematic but no board layout.

About the PitBox PCB

PitBox is an open source ESP32 PCB design by Titouan-Beaurepaire, published on GitHub. It is a board, with 49 components from 32 distinct parts.

Its main chip is the ESP32-S3-WROOM-1-N8, from the ESP32 family. Other key parts include the AP63203WU, SN65HVD230 and USBLC6-2SC6. By type, the board carries 17 resistors, 12 capacitors, 8 diodes, 4 ICs, 4 connectors and 2 switches.

It belongs with the iot & wireless designs in this gallery.

From the project

Boîtier de télémétrie OBD-II : Arduino, bus CAN, carte SD et dashboard web en direct

Boîtier de télémétrie OBD-II : il lit les données du calculateur moteur sur le bus CAN, les enregistre sur carte SD, les affiche sur des LEDs dans l'habitacle et les envoie en direct à un dashboard web.

- Architecture - Organisation du dépôt - Matériel - Branchements - Protocole des trames - Sécurité du bus CAN - Firmware - Dashboard - Carte électronique - Workflow Git - Feuille de route

Main components on the PitBox

PitBox bill of materials (BOM)

49 components, 32 distinct parts.

QtyPartRefs
1
AP63203WU
U1
1
ESP32-S3-WROOM-1-N8
U2
1
SN65HVD230
U3
1
USBLC6-2SC6
U4
1
OBD
J1
1
microSD
J2
1
USB-C
J3
1
UART debug
J4
1
500mA
F1
1
RESET
SW1
1
BOOT
SW2
1
SS34
D1
1
SMBJ24CA
D2
1
SS34 (USB)
D3
1
Blanche
D4
1
Rouge
D5
1
Verte
D6
1
Jaune
D7
1
Bleue
D8
1
4.7uH 2A
L1
Show 12 more
QtyPartRefs
1
10uF 50V
C1
1
100nF 50V
C2
4
100nF
C3, C6, C8, C10
2
22uF 10V
C4, C5
2
10uF
C7, C11
1
1uF
C9
1
4.7uF
C12
1
100k
R1
1
22k
R2
8
10k
R3, R4, R5, R6, R7, R8, R9, R10
5
330
R11, R12, R13, R14, R15
2
5.1k
R16, R17

PitBox design files

The KiCad project lives in the Titouan-Beaurepaire/PitBox repository on GitHub; these links point at the commit this page was built from.

PitBox: common questions

What microcontroller does the PitBox use?

The PitBox is built around the ESP32-S3-WROOM-1-N8, from the ESP32 family.

How many components are on the PitBox?

49 components, from 32 distinct parts. The full bill of materials is listed on this page.

Where can I download the PitBox design files?

From the Titouan-Beaurepaire/PitBox repository on GitHub, which has the schematic; the links under Design files point to each one.

Can I use the PitBox design in my own project?

The repository has no license, so all rights stay with Titouan-Beaurepaire. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the PitBox without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

Similar boards