Rubber ducky
TomasD-git·Rubber-ducky·Rubber Ducky/Rubber Ducky.kicad_pcb
About the Rubber ducky PCB
Rubber ducky is an open source ESP32 PCB design by TomasD-git, published on GitHub under the GPL-3.0 license. It is a 4-layer board measuring 17.3 × 46.7 mm, with 47 components from 26 distinct parts.
Its main chip is the ESP32-S3, from the ESP32 family. Other key parts include the W25Q32JVSSIQ, RT9013-33GB, XUSM-0930-2319, SS24FL and W25Q256JVEIQ. By type, the board carries 25 capacitors, 8 resistors, 7 ICs, 4 inductors, 1 crystal and 1 antenna.
It belongs with the iot & wireless designs in this gallery.
From the project
small rubber ducky
First buy PCB, with stencil if u dont trust your soldering skills or without if u do. then all components in the bom, u can skip solder paste, kapton tape, hot air station if u have these, once arrived 3D print case solder 4 core cable, plug usbc into pc, flash and then just assemble and you are ready.
Main components on the Rubber ducky
Rubber ducky bill of materials (BOM)
47 components, 26 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | W25Q32JVSSIQ W25Q32JVSSIQ_C179173 Winbond(华邦) | SOIC-8_L5.3-W5.3-P1.27-LS8.0-BL | U1 |
| 1 | ESP32-S3 | QFN-56-1EP_7x7mm_P0.4mm_EP5.6x5.6mm | U2 |
| 1 | RT9013-33GB RICHTEK(立锜) | SOT-23-5_L3.0-W1.7-P0.95-LS2.8-BL | U3 |
| 1 | XUSM-0930-2319 LX(连欣科技) | USB-A-SMD_XUSM-0930-2319 | U4 |
| 2 | SS24FL SS24FL_C894433 onsemi(安森美) | SOD-123FL_L2.8-W1.8-LS3.6-RD | U6, U8 |
| 1 | W25Q256JVEIQ W25Q256JVEIQTR Winbond(华邦) | WSON-8_L8.0-W6.10-P1.27-BL-EP | U7 |
| 1 | 40MHZ 40MHz | Crystal_SMD_3225-4Pin_3.2x2.5mm_HandSoldering | Y1 |
| 1 | 2450AT18A100E JOHANSON(约翰逊) | ANT-SMD_L3.2-W1.6 | AE1 |
| 1 | GT-USB-8016B G-Switch(品赞) | USB-SMD_GT-USB-8016B | USB2 |
| 1 | 2NH 2nH | L_0402_1005Metric_Pad0.77x0.64mm_HandSolder | L1 |
| 1 | 24NH 24nH | L_0603_1608Metric_Pad1.05x0.95mm_HandSolder | L2 |
| 1 | 2.7NH 2.7nH | L_0402_1005Metric_Pad0.77x0.64mm_HandSolder | L3 |
| 1 | 3.9NH 3.9nH | L_0402_1005Metric_Pad0.77x0.64mm_HandSolder | L4 |
| 9 | 100NF 100nF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1, C2, C5, C6, C11, C12, C13, C16 +1 |
| 3 | 1UF 1uF | C_0805_2012Metric | C3, C4, C7 |
| 3 | 10UF 10uF | C_1206_3216Metric | C8, C9, C15 |
| 2 | 1UF 1uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C10, C14 |
| 1 | 10NF 10nF | C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C17 |
| 2 | 12PF 12pF | C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C18, C19 |
| 2 | 1.5PF 1.5pF | C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C20, C21 |
Show 6 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 1.2PF 1.2pF | C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C22 |
| 1 | 0.5PF 0.5pF | C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C23 |
| 1 | 100UF 100uF | C_1210_3225Metric | C24 |
| 1 | 5.1K | R_0805_2012Metric | R1 |
| 2 | 22 | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R2, R3 |
| 5 | 10K | R_0805_2012Metric | R4, R5, R10, R12, R13 |
Rubber ducky design files
The KiCad project lives in the TomasD-git/Rubber-ducky repository on GitHub; these links point at the commit this page was built from.
Rubber ducky: common questions
What microcontroller does the Rubber ducky use?
The Rubber ducky is built around the ESP32-S3, from the ESP32 family.
How big is the Rubber ducky PCB?
The Rubber ducky measures 17.3 × 46.7 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the Rubber ducky?
47 components, from 26 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Rubber ducky design files?
From the TomasD-git/Rubber-ducky repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Rubber ducky design in my own project?
Yes, under the terms of its GPL-3.0 license, which TomasD-git chose for the repository.
Can I test firmware for the Rubber ducky without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k