Alacer-1
tomatencode·Alacer-1
About the Alacer-1 PCB
Alacer-1 is an open source STM32 PCB design by tomatencode, published on GitHub. It is a 4-layer board measuring 50 × 40 mm, with 79 components from 34 distinct parts.
Its main chip is the STM32F411CEUX, from the STM32 family. Other key parts include the DW01A, FS8205A, MT3608B, XC6206P332MR-G and TDK_ICM-45686_SPI. By type, the board carries 36 resistors, 22 capacitors, 8 ICs, 4 transistors, 4 diodes and 2 inductors.
Main components on the Alacer-1
Alacer-1 bill of materials (BOM)
79 components, 34 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | STM32F411CEUX STM32F411CEUx | QFN-48-1EP_7x7mm_P0.5mm_EP5.6x5.6mm | U1 |
| 1 | DW01A | SOT-23-6 | U2 |
| 1 | FS8205A | SOT-23-6 | U3 |
| 1 | MT3608B | SOT-23-6 | U4 |
| 1 | XC6206P332MR-G | SOT-23 | U5 |
| 1 | TDK_ICM-45686_SPI | LGA-14_3x2.5mm_P0.5mm_LayoutBorder3x4y | U7 |
| 1 | W25Q32JVSS | SOIC-8_5.3x5.3mm_P1.27mm | U9 |
| 1 | MS5611-01BA | LGA-8_3x5mm_P1.25mm | U10 |
| 1 | MMBT5551L | SOT-23 | Q1 |
| 3 | IRF7832TRPBF | SO-8_3.9x4.9mm_P1.27mm | Q2, Q3, Q4 |
| 1 | 16MHZ 16Mhz | Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | C173752 Battery_Cell | JST_PH_S2B-PH-K_1x02_P2.00mm_Horizontal | BT1 |
| 1 | C18623826 Buzzer | HYG-8503A-5027 | BZ1 |
| 1 | C5123492 LED green | LED_0805_2012Metric | D1 |
| 1 | C41410771 D_Schottky | D_SMA | D2 |
| 1 | C51933307 LED red | LED_0805_2012Metric | D3 |
| 1 | C2296 LED yellow | LED_0805_2012Metric | D4 |
| 1 | 120R | L_0603_1608Metric | FB1 |
| 1 | 4U7 4u7 1264EY-100M=P3 | L_Chilisin_BMRB00050518-B | L1 |
| 11 | 100N 100n | C_0402_1005Metric | C1, C4, C6, C8, C9, C10, C13, C19 +3 |
Show 14 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | 12P 12p | C_0402_1005Metric | C2, C5 |
| 2 | 10U 10u | C_0805_2012Metric | C3, C18 |
| 1 | 2.2U 2.2u | C_0805_2012Metric | C7 |
| 2 | 1u | C_0402_1005Metric | C11, C12 |
| 2 | 22U 22u | C_0805_2012Metric | C14, C15 |
| 2 | 1u | C_0603_1608Metric | C16, C17 |
| 6 | 100R | R_0402_1005Metric | R1, R5, R18, R19, R23, R27 |
| 14 | 10K 10k | R_0402_1005Metric | R2, R4, R7, R11, R12, R14, R20, R24 +6 |
| 6 | 1k | R_0402_1005Metric | R6, R16, R21, R25, R29, R31 |
| 6 | 47K 47k | R_0402_1005Metric | R8, R15, R17, R22, R26, R30 |
| 1 | 110K 110k | R_0603_1608Metric | R9 |
| 1 | 15K 15k | R_0402_1005Metric | R10 |
| 1 | 68R | R_0603_1608Metric | R13 |
| 1 | 2k | R_0402_1005Metric | R32 |
Alacer-1 design files
The KiCad project lives in the tomatencode/Alacer-1 repository on GitHub; these links point at the commit this page was built from.
- LayoutAlacer-1.kicad_pcb
- SchematicAlacer-1.kicad_sch
- BOMproduction/bom.csv
Alacer-1: common questions
What microcontroller does the Alacer-1 use?
The Alacer-1 is built around the STM32F411CEUX, from the STM32 family.
How big is the Alacer-1 PCB?
The Alacer-1 measures 50 × 40 mm, has 4 copper layers and is 1.5842 mm thick.
How many components are on the Alacer-1?
79 components, from 34 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Alacer-1 design files?
From the tomatencode/Alacer-1 repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Alacer-1 design in my own project?
The repository has no license, so all rights stay with tomatencode. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Alacer-1 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k