6 open source boards using the MT3608B
Real designs built with the MT3608B, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Nordic nRF
Ikoka nano meshtastic device
ndoo
40 × 40 mm18 parts2LCERN-OHL-P-2.0104BirbMesh-One
KokoSoft
47 × 27.7 mm37 parts2LCERN-OHL-S-2.07ESP32
WellD
kinggh0stee
100 × 55 mm99 parts2LMIT2STM32
Kinematic outfits
ZephyrCloudNine
74.9 × 57.2 mm82 parts4LNo license0STM32
Alacer-1
tomatencode
50 × 40 mm79 parts4LNo license0RP2040/RP2350
Mck parting board
preyneyv
136.6 × 66.5 mm67 parts4LNo license0
How designs wire the MT3608B
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the MT3608B connects to, and the resistors, capacitors and other passives placed on it.
- The SW pin has a inductor on 4 of 4 designs, most often 4.7 µH (then 6.8 µH).
- The FB pin has a pull-up to VCC_E22 on 4 of 4 designs, most often 300 kΩ (then 110 kΩ).
- The FB pin has a resistor to GND on 4 of 4 designs, most often 39 kΩ (then 15 kΩ).
- The IN pin has a capacitor to GND on 3 of 4 designs, most often 22 µF.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| SWpin 1 | Connected to: Signal 100% |
|
| GNDpin 2 | Connected to: GND 100% | — |
| FBpin 3 | Connected to: Signal 100% |
|
| ENpin 4 | Connected to: VBATT 50% · a signal 50% |
|
| INpin 5 | Connected to: VBATT 50% · a signal 50% |
|
| NCpin 6 | Connected to: Not connected 100% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Ikoka nano meshtastic device by ndoo, BirbMesh-One by KokoSoft, Mck parting board by preyneyv and Alacer-1 by tomatencode.
The MT3608B in open source designs
The gallery holds 6 open source boards using the MT3608B from 6 GitHub repositories; a typical one measures about 62.5 × 47.5 mm and carries around 73 components.
50% are two-layer designs, the rest use four layers or more, and 50% carry an open source license.
The most starred is Ikoka nano meshtastic device by ndoo.
Parts used alongside the MT3608B
Microcontrollers on boards using the MT3608B
What boards using the MT3608B are built for
MT3608B: common questions
Where can I find a MT3608B reference design?
Each of the 6 boards on this page is a real design using the MT3608B. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the MT3608B SW pin connected?
The SW pin has a inductor on 4 of 4 designs, most often 4.7 µH (then 6.8 µH). Counted from the KiCad layouts of 5 open source designs using the MT3608B.
What pull-up resistor is used on the MT3608B FB pin?
The FB pin has a pull-up to VCC_E22 on 4 of 4 designs, most often 300 kΩ (then 110 kΩ). Counted from the KiCad layouts of 5 open source designs using the MT3608B.
How is the MT3608B IN pin connected?
The IN pin has a capacitor to GND on 3 of 4 designs, most often 22 µF. Counted from the KiCad layouts of 5 open source designs using the MT3608B.
Which microcontrollers do boards using the MT3608B use?
Most are built on STM32 (2), ESP32 (1), Nordic nRF (1) and RP2040/RP2350 (1).
How big is a typical board using the MT3608B?
The median is 62.5 × 47.5 mm, and 50% are two-layer designs.
What is the most popular open source board using the MT3608B?
By GitHub stars, Ikoka nano meshtastic device by ndoo, with 104 stars.
Can I simulate one of these boards using the MT3608B before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.