ブレッドボード 2
torica-org·26th_PCB_AirData·Prototype_2(~12月)/ブレッドボード_2/ブレッドボード_2.kicad_pcb
About the ブレッドボード 2 PCB
ブレッドボード 2 is an open source ESP32 PCB design by torica-org, published on GitHub. It is a 2-layer board measuring 100 × 23.5 mm, with 10 components from 5 distinct parts.
Its main chip is the XIAO-ESP32-S3-SMD, from the ESP32 family. Other key parts include the MCP1703AX-120XXDB. By type, the board carries 6 ICs and 4 connectors.
From the project
メイン兼エアデータセンサー部(今後、エアデータと言います)のリポジトリです。
- 同一レイヤー上で配線する(front面とback面を行き来しない) - できるだけ配線を曲げず,一直線に配線する - 電源線(5V,3.3Vなど)を近くに置かない - Type-Cに接続するときに配線幅を変える必要がある場合,ティアドロップ(フィレット的な機能,以下「ティアドロップの使用」参照)を使用して滑らかに幅を変化させる
例えば2層基板なら1層目と2層目の間の絶縁体を誘電体としたコンデンサにならないようにする. 1つ目の目的でビアを使うのは一般的ですが,2つ目のコンデンサになるのを防ぐ目的でビアを使用しているか確認してください.置く位置はfrontとbackのベタGNDが重なっているところで,角になっている部分や近くにビアがないところです.定期的に配置することでコンデンサ化を防ぐ効果が高まります.
Main components on the ブレッドボード 2
ブレッドボード 2 bill of materials (BOM)
10 components, 5 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 5 | MCP1703AX-120XXDB MCP1703Ax-120xxDB | Converter_DCDC_RECOM_R-78E-0.5_THT | U1, U2, U3, U4, U5 |
| 1 | XIAO-ESP32-S3-SMD | Seeeduino XIAO-MOUDLE14P-2.54-21X17.8MM | U6 |
| 2 | CONN_01X12_SOCKET Conn_01x12_Socket | PinSocket_2x06_P2.54mm_Vertical | J1, J6 |
| 1 | BMP390 | PinSocket_1x04_P2.54mm_Vertical | J2 |
| 1 | LiPo | PA_Connector_Post_2Pin | J3 |
ブレッドボード 2 design files
The KiCad project lives in the torica-org/26th_PCB_AirData repository on GitHub; these links point at the commit this page was built from.
ブレッドボード 2: common questions
What microcontroller does the ブレッドボード 2 use?
The ブレッドボード 2 is built around the XIAO-ESP32-S3-SMD, from the ESP32 family.
How big is the ブレッドボード 2 PCB?
The ブレッドボード 2 measures 100 × 23.5 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the ブレッドボード 2?
10 components, from 5 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the ブレッドボード 2 design files?
From the torica-org/26th_PCB_AirData repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the ブレッドボード 2 design in my own project?
The repository has no license, so all rights stay with torica-org. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the ブレッドボード 2 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in 26th_PCB_AirData
RP2040/RP2350
TORICAberry Pi Bico(3rd Edition)
torica-org
24.2 × 33.9 mm46 parts2LNo license0BNO055
torica-org
17.2 × 17.1 mm20 parts2LNo license0ブレッドボード 3
torica-org
100 × 23.5 mm12 parts2LNo license0Teseo-LIV3FL(GNSS module)
torica-org
17 × 27.5 mm8 parts2LNo license0ICS
torica-org
10.3 × 10.7 mm6 parts2LNo license0ブレッドボード 1
torica-org
52.2 × 23.5 mm5 parts2LNo license0
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k