BigBoy.stretch bkup

transistorfet·retroverse·components/bigboy/hardware/BigBoy/BigBoy.stretch_bkup.kicad_pcb

BigBoy.stretch bkup PCB layout, top view — open source STM32 board by transistorfet

About the BigBoy.stretch bkup PCB

BigBoy.stretch bkup is an open source STM32 PCB design by transistorfet, published on GitHub under the MIT license. It is a 4-layer board measuring 160 × 100 mm, with 118 components from 45 distinct parts.

Its main chip is the STM32H743BITx, from the STM32 family. Other key parts include the AP7361EA-33E-13, KC3225Z25.0000C1KX00, LAN8742A, 74ALVC16245DG and Hirose PCN10-128P-2.54DS(72). By type, the board carries 44 capacitors, 36 resistors, 13 connectors, 10 ICs, 6 jumpers and 3 diodes.

It belongs with the retro computing designs in this gallery.

From the project

A collection of VME-based hardware and software for modular computers

Status: Built & Tested but with design issues (see errata)

A generic card with an STM32H7 microcontroller on it that interfaces to the VME bus using GPIO. I had intended to use it as a bus analyzer, but it's a bit too slow for the k30p CPU at 12.5MHz.

BigBoy.stretch bkup, from the project README
From the project README

Main components on the BigBoy.stretch bkup

AP7361EA-33E-13STM32H743BITxKC3225Z25.0000C1KX00LAN8742A74ALVC16245DGHirose PCN10-128P-2.54DS(72)

BigBoy.stretch bkup bill of materials (BOM)

118 components, 45 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
AP7361EA-33E-13
U1
1
STM32H743BITx
U2
1
KC3225Z25.0000C1KX00
U3
1
LAN8742A
U4
5
74ALVC16245DG
U5, U6, U7, U8, U9
1
Hirose PCN10-128P-2.54DS(72)
U10
1
32,768Hz
Y1
3
5V
J1, J2, J4
2
3.3V
J3, J5
1
Conn_ST_STDC14
J6
1
Hirose DM3D-S
J7
1
Amphenol 10118194-0001LF
J8
1
Bel SI-60062-F
J9
1
SPI2
J10
1
USART1
J11
1
I^{2}C1
J12
1
USART2
J13
1
BOOT
JP1
1
USB POWER
JP2
1
USART1
JP3
Show 25 more
QtyPartRefs
1
SPI1
JP4
1
USART2
JP5
1
I^{2}C1
JP6
1
UB1/2
SW1
1
~{RESET}
SW2
1
3.3V
TP1
1
POWER
D1
1
Dialight 5530188F
D2
1
Dialight 5530177F
D3
2
600Ω @ 100MHz (MI0805K601R-10)
L1, L2
2
4.7uF
C1, C2
36
0.1uF
C3, C5, C7, C8, C10, C11, C12, C13 +28
1
1uF
C4
2
2.2uF
C6, C9
2
5pF
C26, C27
1
10uF
C33
11
10k
R1, R3, R8, R9, R14, R15, R16, R21 +3
7
220
R2, R4, R5, R6, R7, R33, R34
7
33
R10, R11, R12, R17, R18, R19, R20
1
51
R13
1
1.5k
R23
1
12.1k
R24
4
50
R25, R26, R27, R28
2
68
R29, R30
2
4.7k
R35, R36

BigBoy.stretch bkup design files

The KiCad project lives in the transistorfet/retroverse repository on GitHub; these links point at the commit this page was built from.

BigBoy.stretch bkup: common questions

What microcontroller does the BigBoy.stretch bkup use?

The BigBoy.stretch bkup is built around the STM32H743BITx, from the STM32 family.

How big is the BigBoy.stretch bkup PCB?

The BigBoy.stretch bkup measures 160 × 100 mm, has 4 copper layers and is 1.6 mm thick.

How many components are on the BigBoy.stretch bkup?

118 components, from 45 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the BigBoy.stretch bkup design files?

From the transistorfet/retroverse repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.

Can I use the BigBoy.stretch bkup design in my own project?

Yes, under the terms of its MIT license, which transistorfet chose for the repository.

Can I test firmware for the BigBoy.stretch bkup without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

More boards in retroverse

Similar boards