Caribou slime
Tropingenie·Caribou-Slime
About the Caribou slime PCB
Caribou slime is an open source ESP32 PCB design by Tropingenie, published on GitHub under the Custom license license. It is a 2-layer board measuring 62.7 × 37.6 mm, with 13 components from 9 distinct parts.
Its main chip is the ESP32-C3_SUPERMINI, from the ESP32 family. Other key parts include the BMI270 and TP4056. By type, the board carries 4 resistors, 3 ICs, 2 diodes, 2 capacitors, 1 connector and 1 switch.
It belongs with the dev boards & breakouts designs in this gallery.
From the project
SlimeVR PCB using ESP32-C3 and BMI 270
SlimeVR PCB using ESP32-C3 and BMI 270 ## Methodology This design is intended to be assembled either completely by hand, or with some PCBA and finished by hand. Component selection is built around this, prioritizing larger form factor SMT components where possible, to ensure compatibility with and minimizing cost of the PCBA, while maintaining relatively simple assembly when done by hand. ## BOM | Component | Choice | Amount | Cost per | Cost with Shipping | Quick Link |…
Main components on the Caribou slime
Caribou slime bill of materials (BOM)
13 components, 9 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-C3_SUPERMINI | MODULE_ESP32-C3_SUPERMINI | U1 |
| 1 | BMI270 | XDCR_BMI270 | U2 |
| 1 | TP4056 | TP4056 Charging Board | U3 |
| 1 | Conn_01x02_MountingPin | JST_PH_B2B-PH-K_1x02_P2.00mm_Vertical | J1 |
| 1 | EG1270 | SW_EG1270 | S1 |
| 2 | B5817W | D_SOD-123 | D1, D2 |
| 2 | 100nF | C_0805_2012Metric | C1, C2 |
| 2 | 10k | R_0805_2012Metric | R1, R2 |
| 2 | 180k | R_0805_2012Metric | R3, R4 |
Caribou slime design files
The KiCad project lives in the Tropingenie/Caribou-Slime repository on GitHub; these links point at the commit this page was built from.
- Layoutcaribou_slime.kicad_pcb
- Schematiccaribou_slime.kicad_sch
Caribou slime: common questions
What microcontroller does the Caribou slime use?
The Caribou slime is built around the ESP32-C3_SUPERMINI, from the ESP32 family.
How big is the Caribou slime PCB?
The Caribou slime measures 62.7 × 37.6 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Caribou slime?
13 components, from 9 distinct parts. The full bill of materials is listed on this page.
Where can I download the Caribou slime design files?
From the Tropingenie/Caribou-Slime repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Caribou slime design in my own project?
It is published under Custom license, which limits how it may be reused; read the license before building on it.
Can I test firmware for the Caribou slime without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k