Tool power supply

UBC-Hacker-Fab·tool-power-supply·tool-power-supply-v1/tool-power-supply-v1.kicad_pcb

Tool power supply PCB layout, top view — open source RP2040/RP2350 board by UBC-Hacker-Fab

About the Tool power supply PCB

Tool power supply is an open source RP2040/RP2350 PCB design by UBC-Hacker-Fab, published on GitHub. It is a 4-layer board measuring 90 × 160 mm, with 121 components from 48 distinct parts.

Its main chip is the SC1631, from the RP2040/RP2350 family. Other key parts include the IRM-90-12, ACS712ELCTR-20A-T, INA226AIDGSR, AP63205WU-7 and AP63203WU-7. By type, the board carries 47 resistors, 20 capacitors, 14 ICs, 12 connectors, 7 transistors and 7 diodes.

It belongs with the power & battery designs in this gallery.

From the project

general power supply for tools

A general-purpose power supply board for HackerFab tools. Rev 1 targets the spin coater (A2212 930KV BLDC through an EMAX ESC) and the tube furnace (up to about 1000 W, switched by an off-board Fotek SSR-60 DA), and also gives general 12 V / 5 V / 3.3 V taps for future tools. A Raspberry Pi Pico 2 monitors and controls it.

Status: rev 1 schematic done, PCB layout restarted at 90 x 160 mm (120 x 80 mm did not fit); a placement is in the project PCB (first pass scripted, see tools/pcbplacement/; the CAN, expander, M3 hole and XT60 changes were laid out by a targeted update on 2026-10-24 that…

Main components on the Tool power supply

Tool power supply bill of materials (BOM)

121 components, 48 distinct parts.

QtyPartRefs
1
IRM-90-12
Mean Well
U1
1
ACS712ELCTR-20A-T
Allegro
U2
3
INA226AIDGSR
TI
U3, U6, U7
1
AP63205WU-7
Diodes Inc
U4
1
AP63203WU-7
Diodes Inc
U5
4
TPS2553DBVR
TI
U8, U9, U10, U11
1
TCA9534PWR
TI
U12
1
SC1631
U13
1
SN65HVD230DR
TI
U14
3
AO4407C
AOS
Q1, Q2, Q3
4
2N7002
Q4, Q5, Q6, Q7
1
HB9500M-9.5-03P-13-00A
AC IN (L, N, PE)
Kangnex
J1
1
HB9500M-9.5-03P-13-00A
AC OUT (L, N, PE)
Kangnex
J2
1
47053-1000
Fan (1 GND, 2 +12V, 3 TACH, 4 PWM)
Molex
J3
7
DB128V-5.08-2P-GN-S
DORABO
J4, J5, J7, J8, J9, J11, J12
1
XT60PB-F
AMASS
J6
1
DB128V-5.08-4P-GN-S
DORABO
J10
1
0314010.HXP (Digikey F3222-ND)
10A
F1
1
0313003.HXP (Digikey F2545-ND; 4A 0313004.HXP swap-in)
3A
F2
1
nSMD050-33V
500mA
TECHFUSE
F3
Show 28 more
QtyPartRefs
2
0ATO003.V (Digikey F5040-ND)
3A
F4, F5
1
0ATO07.5V (Digikey F11167-ND)
7.5A
F6
1
10D241K
RV1
1
PE tie (PE-GND)
SJ3
1
SJ CAN term
SJ4
1
SJ SSR+ (1-2 = 5V, 2-3 = GPIO)
SJ5
1
SJ SSR- (1-2 = MOSFET, 2-3 = GND)
SJ6
1
NCP18XH103F03RB
10k
Murata
TH1
1
KT-0603R
D1
1
1N4148W
D2
1
SMCJ15A
D3
3
NCD0603Y2
D4, D5, D6
1
SS14
D7
2
SLO0630H4R7MTT
4.7uH
Sunltech
L1, L2
11
CC0603KRX7R9BB104
100nF
Yageo
C1, C2, C4, C13, C14, C15, C16, C17 +3
1
RVE100UF35V67RV0072
100uF
C3
2
CL31A106KBHNNNE
10uF
Samsung
C5, C6
2
100nF
C7, C8
4
CL21A226MAQNNNE
22uF
Samsung
C9, C10, C11, C12
11
0603WAF3302T5E
33k
Uni-Royal
R1, R2, R3, R4, R8, R10, R12, R28 +3
1
RLP25FEGMR005
5m
TA-I
R5
22
0603WAF1002T5E
10k
Uni-Royal
R6, R9, R11, R13, R14, R15, R16, R17 +14
7
0603WAF4701T5E
4.7k
Uni-Royal
R7, R32, R34, R38, R39, R43, R45
1
0603WAF1501T5E
1.5k
Uni-Royal
R20
1
0603WAF6800T5E
680
Uni-Royal
R21
2
RLS12FTCR033
33m
TA-I
R22, R23
1
0603WAF1200T5E
120
Uni-Royal
R41
1
0603WAF1001T5E
1k
Uni-Royal
R42

Tool power supply design files

The KiCad project lives in the UBC-Hacker-Fab/tool-power-supply repository on GitHub; these links point at the commit this page was built from.

Tool power supply: common questions

What microcontroller does the Tool power supply use?

The Tool power supply is built around the SC1631, from the RP2040/RP2350 family.

How big is the Tool power supply PCB?

The Tool power supply measures 90 × 160 mm, has 4 copper layers and is 1.6 mm thick.

How many components are on the Tool power supply?

121 components, from 48 distinct parts. The full bill of materials is listed on this page.

Where can I download the Tool power supply design files?

From the UBC-Hacker-Fab/tool-power-supply repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Tool power supply design in my own project?

The repository has no license, so all rights stay with UBC-Hacker-Fab. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Tool power supply without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug RP2040/RP2350 firmware against it before you order a PCB.

Similar boards