5 open source boards using the SC1631

Real designs built with the SC1631, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

5 boardsClear filters|Most starred

How designs wire the SC1631

Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the SC1631 connects to, and the resistors, capacitors and other passives placed on it.

  • The 3V3_36 pin is tied to 3.3V on 5 of 5 designs.
  • The 3V3_EN_37 pin is left unconnected on 5 of 5 designs.
  • The ADC_VREF_35 pin is left unconnected on 4 of 5 designs.
  • The GPIO4_6 pin has a pull-up to 3.3V on 3 of 5 designs, most often 4.7 kΩ (then 2.2 kΩ).
GND_3pin 3Connected to: GND 100%
GPIO2_4pin 4Connected to: A connector 40% · not connected 20%
  • Pull-up to 3.3V on 40% · 10 kΩ (1), 2.2 kΩ (1)
GPIO4_6pin 6Connected to: Signal 100%
  • Pull-up to 3.3V on 60% · 4.7 kΩ (2), 2.2 kΩ (1)
GPIO5_7pin 7Connected to: Signal 100%
  • Pull-up to 3.3V on 60% · 4.7 kΩ (2), 2.2 kΩ (1)
GND_8pin 8Connected to: GND 100%
GND_13pin 13Connected to: GND 100%
GND_18pin 18Connected to: GND 100%
GPIO14_19pin 19Connected to: Signal 80% · not connected 20%
  • Pull-up to 3.3V on 40% · 10 kΩ (1), 4.7 kΩ (1)
GPIO15_20pin 20Connected to: A connector 40% · not connected 20%
  • Pull-up to 3.3V on 40% · 10 kΩ (1), 4.7 kΩ (1)
GND_23pin 23Connected to: GND 100%
GPIO18_24pin 24Connected to: Signal 80% · not connected 20%
  • Series resistor on 40% · 1 kΩ (1), 4.02 kΩ (1)
GPIO21_27pin 27Connected to: Not connected 60% · a signal 40%
GND_28pin 28Connected to: GND 100%
RUN_30pin 30Connected to: Not connected 60% · a signal 40%
  • Pull-up to 3.3V on 40% · 1.5 kΩ (1), 100 kΩ (1)
GPIO26_ADC0_31pin 31Connected to: Signal 80% · not connected 20%
  • Resistor to GND on 40% · 10 kΩ (1), 100 kΩ (1)
  • Series resistor on 40% · 4.7 kΩ (1), 47 Ω (1)
GPIO27_ADC1_32pin 32Connected to: Not connected 60% · a signal 40%
AGND_33pin 33Connected to: GND 80% · not connected 20%
ADC_VREF_35pin 35Connected to: Not connected 80% · 3.3V 20%
3V3_36pin 36Connected to: 3.3V 100%
3V3_EN_37pin 37Connected to: Not connected 100%
GND_38pin 38Connected to: GND 100%
VSYS_39pin 39Connected to: Not connected 60% · 5V 20% · a signal 20%
VBUS_40pin 40Connected to: Not connected 60% · VBUS 20% · a signal 20%

17 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Pico CAN-FD Adapter by RealtimeRoboticsGroup, Tool power supply by UBC-Hacker-Fab, Sniffer by OpenRemise and Usb c cable analyzer by rwjblue.

The SC1631 in open source designs

The gallery holds 5 open source boards using the SC1631 from 5 GitHub repositories; a typical one measures about 90 × 125 mm and carries around 71 components.

60% are two-layer designs, the rest use four layers or more, and 20% carry an open source license.

The most starred is Tool power supply by UBC-Hacker-Fab.

Microcontrollers on boards using the SC1631

What boards using the SC1631 are built for

SC1631: common questions

Where can I find a SC1631 reference design?

Each of the 5 boards on this page is a real design using the SC1631. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the SC1631 3V3_36 pin connected?

The 3V3_36 pin is tied to 3.3V on 5 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the SC1631.

How is the SC1631 3V3_EN_37 pin connected?

The 3V3_EN_37 pin is left unconnected on 5 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the SC1631.

How is the SC1631 ADC_VREF_35 pin connected?

The ADC_VREF_35 pin is left unconnected on 4 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the SC1631.

Which microcontrollers do boards using the SC1631 use?

Most are built on RP2040/RP2350 (5).

How big is a typical board using the SC1631?

The median is 90 × 125 mm, and 60% are two-layer designs.

What is the most popular open source board using the SC1631?

By GitHub stars, Tool power supply by UBC-Hacker-Fab, with 1 stars.

Can I simulate one of these boards using the SC1631 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part